ASTM A1064/A1064M-10e1

Name: ASTM A1064/A1064M-10e1
Brand: ASTM
SKU: astm-a1064-a1064m-10e1

system ASTM 2013-03-11 13 PDF 461 0 2026-07-03 18:35

/ 11

100%

loading preview...

summary

Standard Specification for Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete

description

Scope

1.1 This specification covers steel wire and welded wire reinforcement produced from hot-rolled rod to be used for the reinforcement of concrete. The steel wire is cold-worked, drawn or rolled, plain (non-deformed, as-drawn or galvanized), or deformed. Welded wire reinforcement is made from plain or deformed wire, or a combination of plain and deformed wire. Common wire sizes and dimensions are given in Table 1, Table 2, Table 3, and Table 4. Actual wire sizes are not restricted to those shown in the tables.

TABLE 1 Dimensional Requirements for Plain Wire—Inch-Pound Units^A

Size Number^B^,^C^,^D	Nominal Diameter in. [mm]^E	Nominal Area in.² [mm²]
W 0.5	0.080 [2.03]	0.005 [3.23]
W 1.2	0.124 [3.14]	0.012 [7.74]
W 1.4	0.134 [3.39]	0.014 [9.03]
W 2	0.160 [4.05]	0.020 [12.9]
W 2.5	0.178 [4.53]	0.025 [16.1]
W 2.9	0.192 [4.88]	0.029 [18.7]
W 3.5	0.211 [5.36]	0.035 [22.6]
W 4	0.226 [5.73]	0.040 [25.8]
W 4.5	0.239 [6.08]	0.045 [29.0]
W 5	0.252 [6.41]	0.050 [32.3]
W 5.5	0.265 [6.72]	0.055 [35.5]
W 6	0.276 [7.02]	0.060 [38.7]
W 8	0.319 [8.11]	0.080 [51.6]
W 10	0.357 [9.06]	0.100 [64.5]
W 11	0.374 [9.50]	0.110 [71.0]
W 12	0.391 [9.93]	0.120 [77.4]
W 14	0.422 [10.7]	0.140 [90.3]
W 16	0.451 [11.5]	0.160 [103]
W 18	0.479 [12.2]	0.180 [116]
W 20	0.505 [12.8]	0.200 [129]
W 22	0.529 [13.4]	0.220 [142]
W 24	0.553 [14.0]	0.240 [155]
W 26	0.575 [14.6]	0.260 [168]
W 28	0.597 [15.2]	0.280 [181]
W 30	0.618 [15.7]	0.300 [194]
W 31	0.628 [16.0]	0.310 [200]
W 45	0.757 [19.2]	0.450 [290]

^A Table 1 should be used on projects that are designed using inch-pound units; Table 2 should be used on projects that are designed using SI units.

^B The number following the prefix indicates the nominal cross-sectional area of the wire in square inches multiplied by 100.

^C For sizes other than those shown above, the Size Number shall be the number of one hundredth of a square inch in the nominal area of the wire cross section, prefixed by the W.

^D These sizes represent the most readily available sizes in the welding wire reinforcement industry. Other wire sizes are available and many manufactures can produce them in 0.0015 in.² increments.

^E The nominal diameter is based on the nominal area of the wire.

TABLE 2 Dimensional Requirements for Plain Wire—SI Units^A

Size Number^B^,^C^,^D	Nominal Diameter mm [in.]^E	Nominal Area mm² [in.²]
MW 5	2.52 [0.099]	5 [0.008]
MW 10	3.57 [0.140]	10 [0.016]
MW 15	4.37 [0.172]	15 [0.023]
MW 20	5.05 [0.199]	20 [0.031]
MW 25	5.64 [0.222]	25 [0.039]
MW 30	6.18 [0.243]	30 [0.047]
MW 35	6.68 [0.263]	35 [0.054]
MW 40	7.14 [0.281]	40 [0.062]
MW 45	7.57 [0.298]	45 [0.070]
MW 50	7.98 [0.314]	50 [0.078]
MW 55	8.37 [0.329]	55 [0.085]
MW 60	8.74 [0.344]	60 [0.093]
MW 65	9.10 [0.358]	65 [0.101]
MW 70	9.44 [0.372]	70 [0.109]
MW 80	10.1 [0.397]	80 [0.124]
MW 90	10.7 [0.421]	90 [0.140]
MW 100	11.3 [0.444]	100 [0.155]
MW 120	12.4 [0.487]	120 [0.186]
MW 130	12.9 [0.507]	130 [0.202]
MW 200	16.0 [0.628]	200 [0.310]
MW 290	19.2 [0.757]	290 [0.450]

^A The wire sizes in Table 1 should be used on projects that are designed using inch-pound units; the wire sizes in Table 2 should be used on projects that are designed using SI units.

^B The number following the prefix indicates the nominal cross-sectional area of the wire in square milimetres.

^C For sizes other than those shown above, the Size Number shall be the number of square millimetres in the nominal area of the wire cross section, prefixed by the MW.

^D These sizes represent the most readily available sizes in the welding wire reinforcement industry. Other wire sizes are available and many manufactures can produce them in 1 mm² increments.

^E The nominal diameter is based on the nominal area of the wire.

TABLE 3 Dimensional Requirements for Deformed Wire—Inch-Pound Units

Nominal Dimensions				Deformation Requirements
Deformed Wire Size^A^,^B^,^C^,^D	Unit Weight, lb/ft	Diameter, in.^E	Cross-Sectional Area, in.² ^F	Minimum Average Height of Deformations, in.^G^,^H^,^I
D1	0.034	0.113	0.010	0.0045
D2	0.068	0.160	0.020	0.0063
D3	0.102	0.195	0.030	0.0078
D4	0.136	0.226	0.040	0.0101
D5	0.170	0.252	0.050	0.0113
D6	0.204	0.276	0.060	0.0124
D7	0.238	0.299	0.070	0.0134
D8	0.272	0.319	0.080	0.0143
D9	0.306	0.339	0.090	0.0152
D10	0.340	0.357	0.100	0.0160
D11	0.374	0.374	0.110	0.0187
D12	0.408	0.391	0.120	0.0195
D13	0.442	0.407	0.130	0.0203
D14	0.476	0.422	0.140	0.0211
D15	0.510	0.437	0.150	0.0218
D16	0.544	0.451	0.160	0.0225
D17	0.578	0.465	0.170	0.0232
D18	0.612	0.479	0.180	0.0239
D19	0.646	0.492	0.190	0.0245
D20	0.680	0.505	0.200	0.0252
D21	0.714	0.517	0.210	0.0259
D22	0.748	0.529	0.220	0.0265
D23	0.782	0.541	0.230	0.0271
D24	0.816	0.553	0.240	0.0277
D25	0.850	0.564	0.250	0.0282
D26	0.884	0.575	0.260	0.0288
D27	0.918	0.586	0.270	0.0293
D28	0.952	0.597	0.280	0.0299
D29	0.986	0.608	0.290	0.0304
D30	1.02	0.618	0.300	0.0309
D31	1.05	0.628	0.310	0.0314
D45	1.53	0.757	0.450	0.0379

^A The wire sizes in Table 3 should be used on projects that are designed using inch-pound units; the wire sizes in Table 4 should be used on projects that are designed using SI units.

^B The number following the prefix indicates the nominal cross-sectional area of the deformed wire in square inches multiplied by 100.

^C For sizes other than those shown above, the Size Number shall be the number of one hundredths of a square inch in the nominal area of the deformed wire cross section, prefixed by the D.

^D These sizes represent the most readily available sizes in the welded wire reinforcement industry. Other wire sizes are available and many manufacturers can produce them in 0.0015 in.² increments.

^E The nominal diameter of a deformed wire is equivalent to the nominal diameter of a plain wire having the same weight per foot as the deformed wire.

^F The cross-sectional area is based on the weight of the wire. The area in square inches may be calculated by dividing the weight in pounds by 0.2833 (weight of 1 in.³ of steel) or by dividing the weight per lineal foot of specimen in pounds by 3.4 (weight of steel 1 in. square and 1 foot long).

^G The minimum average height of the deformations shall be determined from measurements made on not less than two typical deformations from each line of deformations on the wire. Measurements shall be made at the center of indentation or between two raised ribs as described in 7.2.4.7.

^H Spacing of deformations shall not be greater than 0.285 in. nor less than 0.182 in. for all wire sizes.

^I See 7.2.4.3 for average number of deformations per unit length.

TABLE 4 Dimensional Requirements for Deformed Wire—SI Units

Nominal Dimensions					Deformation Requirements
Deformed Wire Size^A^,^B^,^C^,^D	D [in.² × 100]	Unit Mass, kg/m	Diameter, mm^E	Cross-Sectional Area, mm² ^F	Minimum Average Height of Deformations, mm^G^,^H^,^I
MD 25	[D 3.9]	0.196	5.64	25	0.252
MD 30	[D 4.7]	0.235	6.18	30	0.279
MD 35	[D 5.4]	0.275	6.68	35	0.302
MD 40	[D 6.2]	0.314	7.14	40	0.320
MD 45	[D 7.0]	0.353	7.57	45	0.342
MD 50	[D 7.8]	0.392	7.98	50	0.360
MD 55	[D 8.5]	0.432	8.37	55	0.378
MD 60	[D 9.3]	0.471	8.74	60	0.392
MD 65	[D 10.1]	0.510	9.10	65	0.455
MD 70	[D 10.9]	0.549	9.44	70	0.470
MD 80	[D 12.4]	0.628	10.1	80	0.505
MD 90	[D 14.0]	0.706	10.7	90	0.535
MD 100	[D 15.5]	0.785	11.3	100	0.565
MD 120	[D 18.6]	0.942	12.4	120	0.620
MD 130	[D 20.2]	1.02	12.9	130	0.645
MD 200	[D 31.0]	1.57	16.0	200	0.800
MD 290	[D 45.0]	2.28	19.2	290	0.961

^A The wire sizes in Table 3 should be used on projects that are designed using inch-pound units; the wire sizes in Table 4 should be used on projects that are designed using SI units.

^B The number following the prefix indicates the nominal cross-sectional area of the deformed wire in square millimetres.

^C For sizes other than those shown above, the Size Number shall be the number of square millimetres in the nominal area of the deformed wire cross section, prefixed by the MD.

^D These sizes represent the most readily available sizes in the welded wire reinforcement industry. Other wire sizes are available and many manufacturers can produce them in 1 mm² increments.

^E The nominal diameter of a deformed wire is equivalent to the nominal diameter of a plain wire having the same weight per metre as the deformed wire.

^F The cross-sectional area is based on the mass of the wire. The area in square millimetres may be calculated by dividing the unit mass in kg/mm by 7.849 × 10^-6 (mass of 1 mm³ of steel) or by dividing the unit mass in kg/m by 0.007849 (mass of steel 1 mm square and 1 m long).

^H Spacing of deformations shall not be greater than 7.24 mm nor less than 4.62 mm for all wire sizes.

^I See 7.2.4.3 for average number of deformations per unit length.

Note 1—Welded wire for concrete reinforcement has historically been described by various terms: welded wire fabric, WWF, fabric, and mesh. The wire reinforcement industry has adopted the term welded wire reinforcement (WWR) as being more representative of the applications of the products being manufactured. Therefore, the term welded wire fabric has been replaced with the term welded wire reinforcement in this specification and in related specifications.

1.2 Supplement S1 describes high-strength wire, which manufacturers furnish when specifically ordered. Manufacturers furnish high-strength wire in place of regular wire if mutually agreed to by the purchaser and the manufacturer.

1.3 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets (except in Table 2 and Table 4). The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values may result in nonconformance with the specification.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Details

Publisher ASTM

File size 134.63 KB

Pages 11

Format PDF

Publication date 2013-03-11

Download with Points

Rating ★★★★★

Points 461

File size 134.63 KB

Pages 11

Format PDF

Publication date 2013-03-11

Free downloads · ASTM A1064/A1064M-10e1

Upload documents and earn points for free downloads.

Share documents, reports, and standards. Approved uploads can earn points that you can use to download documents without paying.

Upload Documents Recharge for Points Social Sharing

Related Products

★★★★★

ASTM A6/A6M-01 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling ★★★★★

ASTM A20/A20M-01 Standard Specification for General Requirements for Steel Plates for Pressure Vessels ★★★★★

ASTM D4328-18 Standard Practice for Calculation of Supersaturation of Barium Sulfate, Strontium Sulfate, and Calcium Sulfate Dihydrate (Gypsum) in Brackish Water, Seawater, and Brines ★★★★★

ASTM D4330-94(2002) Standard Practice for Evaluation of Fiberglass Boat Polish and Wax ★★★★★

ASTM D6954-24 Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation ★★★★★

ASTM D653-26a Standard Terminology Relating to Soil, Rock, and Contained Fluids This ASTM terminology standard defines terms used in soil, rock, groundwater, grouting, geotechnical engineering, and related Committee D18 standards. ★★★★★

ASTM D1003-21 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics ★★★★★

ASTM D613-26 Standard Test Method for Cetane Number of Diesel Fuel Oil This standard establishes a test method for determining the cetane number of diesel fuel oil using a standardized single-cylinder, four-stroke-cycle, variable-compression-ratio diesel engine. ★★★★★

ASTM D3363-22 Standard Test Method for Film Hardness by Pencil Test ★★★★★

ASTM D5329-16 Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements ★★★★★

ASTM D7283-17 Standard Test Method for Alpha and Beta Activity in Water By Liquid Scintillation Counting ★★★★★

Standard Test Method for the Sieve Analysis of Coke This test method determines the size distribution of coke by separating a sample into defined sieve fractions and reporting each fraction as a percentage of the gross sample mass. ★★★★★

ASTM E29-06b Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications ★★★★★

ASTM D5329-15 Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements ★★★★★

ASTM D4329-21 Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics