Abstract
This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction. The castings shall be true to pattern, reasonable smooth, and free from defects that would make the castings unfit for the use for which they are intended. The material shall conform to the chemical composition requirements specified. All centrifugally cast high-silicon iron pipe shall be supplied in the as-cast condition. All other pipe and fittings shall be supplied in the stress-relieved condition; the stress relieving procedures are presented. Acid-proof joints for hub/plain-end pipe shall require the use of an acid-proof rope packing. No-hub pipe and fittings shall require a special acid resistant mechanical joint coupling. High-silicon iron pipe can be cut with either manual or hydraulic snap cutters. Hydrostatic testing shall be conducted on all castings.
Scope
1.1 This specification covers high-silicon iron pipe and pipe fittings intended for corrosion-resistant service for both above- and below-grade construction.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 Pipe and pipe fittings shall be the no-hub (MJ) or the hub and plain end design.
1.4 Pipe and pipe fittings shall be of the sizes specified in Table 1 and Table 2 and Figs. 1-71 or other sizes that shall be permitted to conform to the requirements given herein.
TABLE 1 Tolerances for High-Silicon Iron Hub/Plain-End Pipe
Note 1: 1 in. = 25.4 mm.
| Size, in. | Wall Thickness, in. | ID Tolerance, in. | OD Tolerance, in. |
|  2 | ±1/32 | ±1/32 | ±1/32 |
|  3 | ±1/32 | ±1/32 | ±1/32 |
|  4 | ±1/32 | ±1/32 | ±1/32 |
|  6 | ±1/32 | ±1/32 | ±3/64 |
|  8 | ±1/32 | ±1/8   | ±1/8   |
| 10 | ±1/8   | ±1/8   | ±1/8   |
| 12 | ±1/8   | ±1/8   | ±1/8   |
| 15 | ±1/8   | ±1/8   | ±1/8   |
TABLE 2 Tolerances for High-Silicon Iron Fittings
Note 1: 1 in. = 25.4 mm.
| Size, in. | ID Tolerance, | OD Tolerance, | Stop Lug Depth |
|    11/2 | ±1/16 | ±1/16 | ±1/16 |
|    11/2 × 11/2 | ±1/16 | ±1/16 | ±1/16 |
|    2 | ±1/16 | ±1/16 | ±1/16 |
|    2 × 11/2 | ±1/16 | ±1/16 | ±1/16 |
|    2 × 2 | ±1/16 | ±1/16 | ±1/16 |
|    3 | ±1/16 | ±1/16 | ±1/16 |
|    3 × 11/2 | ±1/16 | ±1/16 | ±1/16 |
|    3 × 2 | ±1/16 | ±1/16 | ±1/16 |
|    3 × 3 | ±1/16 | ±1/16 | ±1/16 |
|    4 | ±1/16 | ±1/16 | ±1/16 |
|    4 × 11/2 | ±1/16 | ±1/16 | ±1/16 |
|    4 × 2 | ±1/16 | ±1/16 | ±1/16 |
|    4 × 3 | ±1/16 | ±1/16 | ±1/16 |
|    4 × 4 | ±1/16 | ±1/16 | ±1/16 |
TABLE 3 Chemical Composition
| Element | Composition, Weight % | |
| Grade 1 | Grade 2 | |
| Carbon |  0.65–1.10 |  0.75–1.15 |
| Manganese |  1.50 max |  1.50 max |
| Silicon | 14.20–14.75 | 14.20–14.75 |
| Chromium |  0.50 max |  3.25–5.00 |
| Molybdenum |  0.50 max |  0.40-0.60 |
| Copper |  0.50 max |  0.50 max |
FIG. 1 No-Hub Pipe (MJ)
| Size, in. | J, in. | F, in. | t, in. |
| 11/2 | 23/16 (2.19) | 84 | 5/16 |
| 2  | 211/16 (2.69) | 84 | 5/16 |
| 3  | 349/64 (3.77) | 84 | 5/16 |
| 4  | 449/64 (4.77) | 84 | 5/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 2 Quarter Bends
| Size, in. | D, in. | ID, in. | OD, in. | Stop Lug |
| 11/2 | 41/4 | 11/2 | 23/16 (2.19) | 11/32 |
| 2 | 41/2 | 2 | 25/8 (2.62) | 11/32 |
| 2 × 11/2 | 43/16 × 41/2 | 2 × 11/2 | 25/8 × 23/16 | 11/32 |
| 3 | 5 | 3 | 33/4 (3.75) | 11/32 |
| 4 | 51/2 | 4 | 43/4 (4.75) | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 3 Sixth Bends
| Size, in. | D, in.   | ID, in.   | OD, in. | Stop Lug |
|    11/2 |    3 |    11/2 |    23/16 | 11/32 |
|    2 |    31/4 |    2 |    25/8 | 11/32 |
|    3 |    31/2 |    3 |    33/4 | 11/32 |
|    4 |    33/4 |    4 |    43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 4 Return Bends
|  Size, |  C, | D, |  F, | R, | ID, | OD, | Stop Lug Depth (P), in. |
|   11/2 |  4 | 2 |  53/32 | 2 | 11/2 |   23/16 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 5 Double-Branch Quarter Bend
| Size, | D, | E, | ID, | OD, | Stop Lug Depth (P), in. |
| 11/2 | 37/8 | 33/4 | 11/2 | 23/16 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 6 Eight Bends
|   Size, |   D, |   ID, |   OD, | Stop Lug Depth (P), in. |
|   11/2 |   21/2 |   11/2 |   23/16 | 11/32 |
|   2 |   23/4 |   2 |   25/8 | 11/32 |
|   3 |   3 |   3 |   33/4 | 11/32 |
|   4 |   31/4 |   4 |   43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 7 Sixteenth Bends
|   Size, |   D, |   ID, |   OD, | Stop Lug Depth (P), in. |
|   11/2 |   2 |   11/2 |   23/16 | 11/32 |
|   2 |   21/8 |   2 |   25/8 | 11/32 |
|   3 |   21/4 |   3 |   33/4 | 11/32 |
|   4 |   23/8 |   4 |   43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 8 Long-Sweep Quarter Bends
FIG. 9 Sanitary Y Branches
| Size, | D, | F, | G, |  ID, | OD, | Stop Lug Depth (P), in. |
| 1/2 × 11/2 | 45/8 |  61/2 | 17/8 | 11/2 × 11/2 | 23/16 × 23/16 | 11/32 |
| 2 × 11/2 | 47/8 |  61/2 | 15/8 | 2 × 11/2 | 25/8 × 23/16 | 11/32 |
| 2 × 2 | 45/8 |  63/8 | 2 | 2 × 2 | 25/8 × 25/8 | 11/32 |
| 3 × 11/2 | 55/8 |  61/2 | 11/4 | 3 × 11/2 | 33/4 × 23/16 | 11/32 |
| 3 × 2 | 57/8 |  71/8 | 11/2 | 3 × 2 | 33/4 × 25/8 | 11/32 |
| 3 × 3 | 63/8 |  85/8 | 21/4 | 3 × 3 | 33/4 × 33/4 | 11/32 |
| 4 × 11/2 | 65/8 |  71/2 | 13/8 | 4 × 11/2 | 43/4 × 23/16 | 11/32 |
| 4 × 2 | 65/8 |  71/2 | 13/8 | 4 × 2 | 43/4 × 25/8 | 11/32 |
| 4 × 3 | 71/8 |  83/4 | 13/4 | 4 × 3 | 43/4 × 33/4 | 11/32 |
| 4 × 4 | 75/8 | 101/4 | 25/8 | 4 × 4 | 43/4 × 43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 10 Double-Branch Sanitary Y
| Size,  | D, | F, | G, | ID,   | OD, | Stop Lug |
| in.  | in. | in. | in. | in.    | in. | Depth (P), in. |
| 11/2 × 11/2 | 45/8 | 61/2 | 17/8 | 11/2 × 11/2 | 23/16 × 23/16 | 11/32 |
| 2 × 11/2 | 47/8 | 61/2 | 15/8 | 2 × 11/2 | 25/8 × 23/16 | 11/32 |
| 2 × 2 | 45/8 | 63/8 | 2 | 2 × 2 | 25/8 × 25/8 | 11/32 |
| 3 × 11/2 | 55/8 | 61/2 | 11/4 | 3 × 11/2 | 33/4 × 23/16 | 11/32 |
| 3 × 2 | 57/8 | 71/8 | 11/2 | 3 × 2 | 33/4 × 25/8 | 11/32 |
| 3 × 3 | 63/8 | 85/8 | 21/4 | 3 × 3 | 33/4 × 33/4 | 11/32 |
| 4 × 2 | 65/8 | 71/2 | 13/8 | 4 × 2 | 43/4 × 25/8 | 11/32 |
| 4 × 3 | 71/8 | 83/4 | 13/4 | 4 × 3 | 43/4 × 33/4 | 11/32 |
| 4 × 4 | 75/8 | 101/4 | 25/8 | 4 × 4 | 43/4 × 43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 11 Sanitary Combination Y and 1/8
Bend
| Size, | D, | E, | F, | G, | ID, | OD, | Stop Lug |
| 11/2 × 11/2 |   43/4 | 53/8 |  61/2 | 17/8 |   1/2 × 11/2 | 23/16 × 23/16 | 11/32 |
| 2 × 11/2 |   43/4 | 53/4 |  61/2 | 15/8 |   2 × 11/2 | 25/8 × 23/16 | 11/32 |
| 2 × 2 |   5 | 57/8 |  65/8 | 17/8 |   2 × 2 | 25/8 × 25/8 | 11/32 |
| 3 × 11/2 |   4 | 51/4 |  61/2 | 15/8 |   3 × 11/2 | 33/4 × 23/16 | 11/32 |
| 3 × 2 |   5 | 61/4 |  71/8 | 11/2 |   3 × 2 | 33/4 × 25/8 | 11/32 |
| 3 × 3 |   61/4 | 7 |  81/2 | 21/4 |   3 × 3 | 33/4 × 33/4 | 11/32 |
| 4 × 11/2 |   45/16 | 61/8 |  65/8 | 13/8 |   4 × 11/2 | 43/4 × 23/16 | 11/32 |
| 4 × 2 |   5 | 63/8 |  73/8 | 13/8 |   4 × 2 | 43/4 × 25/8 | 11/32 |
| 4 × 3 |   6 | 71/4 |  83/4 | 13/4 |   4× 3 | 43/4 × 33/4 | 11/32 |
| 4 × 4 |   73/8 | 8  | 101/4 | 25/8 |   4× 4 | 43/4 × 43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 12 Double-Branch Sanitary Combination Y and 1/8 Bend
| Size, | D, | E, | F, | G, | ID, | OD, | Stop Lug |
| 11/2 × 11/2 |  43/4 |  53/8 |  61/2 | 77/8 | 11/2 × 11/2 | 23/16 × 23/16 | 11/32 |
| 2 × 11/2 |  43/4 |  53/4 |  61/2 | 15/8 | 2 × 11/2 | 25/8 × 23/16 | 11/32 |
| 2 × 2 |  5 |  57/8 |  65/8 | 15/8 | 2 × 2 | 25/8 × 25/8 | 11/32 |
| 3 × 11/2 |  41/4 |  51/4 |  61/2 | 15/8 | 3 × 11/2 | 33/4 × 23/16 | 11/32 |
| 3 × 2 |  5 |  61/4 |  71/8 | 11/2 | 3 × 2 | 33/4 × 25/8 | 11/32 |
| 3 × 3 |  61/4 |  7 |  81/2 | 21/4 | 3 × 3 | 33/4 × 33/4 | 11/32 |
| 4 × 2 |  5 |  63/8 |  73/8 | 13/8 | 4 × 2 | 43/4 × 25/8 | 11/32 |
| 4 × 3 |  6 |  71/4 |  83/4 | 13/4 | 4 × 3 | 43/4 × 33/4 | 11/32 |
| 4 × 4 |  73/8 |   8 | 101/4 | 25/8 | 4 × 4 | 43/4 × 43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 13 Sanitary T Branches
| Size, in. | E, in. | F, in. | G, in. | ID, in. | OD, in. | Stop Lug |
| 11/2 × 11/2 | 41/4 | 63/4 | 41/4 |    11/2 × 11/2 |   23/16 × 23/16 | 11/32 |
| 2 × 11/2 | 41/2 | 63/4 | 41/4 |    2 × 11/2 |   25/8 × 23/16 | 11/32 |
| 2 × 11/2 × 11/2 | 41/2 | 63/4 | 41/4 |    2 × 11/2 × 11/2 |   25/8 × 23/16 × 23/16 | 11/32 |
| 2 × 2 | 41/2 | 67/8 | 41/2 |    2 × 2 |   2 5/8 × 25/8 | 11/32 |
| 3 × 11/2 | 5  | 63/4 | 41/4 |    3 × 11/2 |   33/4 × 23/16 | 11/32 |
| 3 × 2 | 5  | 71/4 | 41/2 |    3 × 2 |   33/4 × 2 5/8 | 11/32 |
| 3 × 3 | 5  | 83/8 | 5   |    3× 3 |   33/4 × 33/4 | 11/32 |
| 4 × 11/2 | 59/16 | 67/8 |  47/32 |    4× 11/2 |   43/4 × 23/16 | 11/32 |
| 4 × 2 | 51/2 | 71/4 | 41/2 |    4 × 2 |   43/4 × 25/8 | 11/32 |
| 4 × 3 | 51/2 | 81/4 | 5   |    4 × 3 |   43/4 × 33/4 | 11/32 |
| 4 × 4 | 51/2 | 93/8 | 51/2 |    4 × 4 |   43/4 × 43/4 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 14 Double-Branch Sanitary T
| Size, | E, | F, | G, | ID, | OD, | Stop Lug |
|  11/2 × 11/2 | 41/4 | 63/4 | 41/4 |  11/2 × 11/2 |   23/16 × 23/16 | 11/32 |
|  2 × 11/2 | 41/2 | 63/4 | 41/4 |  2 × 11/2 |   25/8 × 23/16 | 11/32 |
|  2 × 2 | 41/2 | 67/8 | 41/2 |  2 × 2 |   25/8 × 25/8 | 11/32 |
|  3 × 11/2 | 5 | 63/4 | 41/4 |  3 ×11/2 |   33/4 × 23/16 | 11/32 |
|  3 × 2 | 5 | 71/4 | 41/2 |  3 × 2 |   33/4 × 25/8 | 11/32 |
|  3 × 3 | 5 | 83/8 | 5 |  3 × 3 |   33/4 × 33/4 | 11/32 |
|  4 × 2 | 51/2 | 71/4 | 41/2 |  4 × 2 |   43/8 × 25/8 | 11/32 |
|  4 × 3 | 51/2 | 81/4 | 5 |  4 × 3 |   43/4 × 33/4 | 11/32 |
|  4 × 4 | 51/2 | 93/8 | 51/2 |  4 × 4 |   43/8 × 43/8 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 15 Sanitary Running Traps
| Size, | A, | B, | C, | D, | J, | R, | ID, | OD, | Stop Lug |
|   11/2 |   23/4 |    15/8 |   5 | 10 |   4 |   13/4 |   11/2 |  23/16 |   11/32 |
|   2 |   31/2 |    115/16 |   51/2 | 11 |   4 |   2 |   2 |  25/8 |   11/32 |
|   3 |   4 |    25/16 |   61/2 | 13 |   51/2 |   21/2 |   3 |  33/4 |   11/32 |
|   4 |   41/2 |    3 |   71/2 | 15 |   61/2 |   3 |   4 |  43/4 |   11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 16 Sanitary P Traps
|   Size, |   A, |   B, |   C, |   D, |   J, |   R, |   ID, |   OD, | Stop Lug Depth (P), in. |
|   11/2 |   33/4 |  15/8 |   31/2 |   63/4 |   4 |    13/4 |   11/2 |  23/16 |   11/32 |
|   2 |   4 |  115/16 |   4 |   71/2 |   4 |    2 |   2 |  25/8 |   11/32 |
|   3 |   41/2 |  25/16 |   5 |   9 |   51/2 |    21/2 |   3 |  33/4 |   11/32 |
|   4 |   5 |  3 |   6 |   101/2 |   61/2 |    3 |   4 |  43/4 |   11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 17 Swivel Trap P-Style, Short
|   Size, |   C, |   D, |   E, |   F, |   G, |   H, |   ID, |   OD, | Stop Lug Depth (P), in. |
|   11/2 |   83/4 |   4 |  615/16 |   57/16 |   13/32 |   121/2 |   11/2 |   23/16 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 18 Swivel Trap P-Style, Long
| Size, | CA, | D, | E, | F, | G, | HA, | ID, | OD, | Stop Lug Depth (P), in. |
| 11/2 | 123/4 | 4 | 615/16 | 57/16 | 13/32 | 121/2 | 11/2 | 23/16 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 19 Swivel Type-S Style, Long
|   Size, |   C, |   F, |   G, |   H, |   ID, |   OD, | Stop Lug Depth (P), in. |
|    11/2 |   6 |   8 |   143/8 |   223/4 |   11/2 |   23/16 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 20 Centrifugal Drum Trap P Swivel Type
FIG. 21 Centrifugal Drum Trap S Swivel Type
|   Size, |   C, |   D, |   E, |   F, |   J, |   ID, |   OD, | Stop Lug Depth (P), in. |
|    11/2 |   4 |   53/32 |   63/4 |   123/4 |   4 |   11/2 |   11/8 | 11/32 |
|    11/2 |   4 |   1515/32 |   63/4 |   123/4 |   4 |   11/2 |   11/8 | 11/32 |
|    2 |   43/4 |   511/16 |   79/16 |   141/4 |   43/4 |   2 |   2 | 11/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 22 Combination Cleanout and Test Tees
| Size, in. | B, | E, | F, | G, |
| 2 |      27/16 |     33/4 |     67/8 |      37/16 |
| 3 |      33/8 |     411/16 |     83/8 |      43/16 |
| 4 |      37/8 |     57/16 |     93/8 |      411/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 23 Coupling
| Size, in. | A, in. | B, in. |
|  11/2 |    33/8 |    27/8 |
| 2 |    4 |    33/8 |
| 3 |    47/16 |    43/16 |
| 4 |    415/16 |    53/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 24 Pipe Plugs
| Size, in. | F, in. |
| 1/2 | 2  |
| 2 | 21/2 |
| 3 | 21/2 |
| 4 | 21/2 |
Note 1: 1 in. = 25.4 mm.
FIG. 25 Cleanout Plugs
| Size, in. | A, in. | D, in. | E, in. | F, in. |
|    11/2 | 23/16 | 21/4 | 15/16 | 39/16 |
|    2 | 221/32 | 21/4 | 15/16 | 39/16 |
|    3 | 33/4 | 21/2 | 13/8 | 37/8 |
|    4 | 43/4 | 23/4 | 17/16 | 43/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 26 Adapter/Hub to No-Hub
| Size, in.    | A, in. | B, in. | E, in. | F, in. |
| 11/2 × 11/2 | 323/32 | 21/4 | 9/16 | 45/8 |
| 11/2 × 2 | 313/16 | 221/32 | 9/16 | 45/8 |
| 11/2 × 3 | 313/16 | 313/16 | 9/16 | 45/8 |
| 11/2 × 4 | 313/16 | 413/16 | 9/16 | 47/8 |
| 2 × 2 | 45/16 | 223/32 | 5/8 | 51/8 |
| 2 × 3 | 45/16 | 313/16 | 5/8 | 43/4 |
| 2 × 4 | 45/16 | 413/16 | 5/8 | 5 |
| 3 × 3 | 55/16 | 313/16 | 11/16 | 53/8 |
| 4 × 4 | 69/32 | 47/8 | 11/16 | 59/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 27 Reducers-Increasers
| Size, in. | B, in. | F, in. |
|     2 × 11/2 | 11/2 | 8 |
|     3 × 11/2 | 11/2 | 8 |
|     3 × 2 | 11/2 | 8 |
|     4 × 11/2 | 11/2 | 8 |
|     4 × 2 | 11/2 | 8 |
|     4 × 3 | 11/2 | 8 |
Note 1: 1 in. = 25.4 mm.
FIG. 28 Sink Outlet
| Size, in. | A, in. | B, in. | C, in. | D, in. | E, in. | F, in. |
| 11/2 | 0 to 2 | 101/4 | 17/8 | 35/16 | 1/4 | 23/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 29 Sink Overflows
| A, in.A | B, in.A | C, in. |
| 4 |  61/8 | 1 |
| 6 |  81/8 | 1 |
| 8 | 101/8 | 1 |
Note 1: 1 in. = 25.4 mm.
FIG. 30 Threaded Adapters
| Type | Size, in. |
| AD-7 |    11/2 Outlet to 11/2 MJ |
| AD-8 |    11/2 Outlet to 2 MJ |
| AD-10 |    2 Outlet to 2 MJ |
Note 1: 1 in. = 25.4 mm.
FIG. 31 Trap Cleanout Details
Note 1: 1 in. = 25.4 mm.
FIG. 32 Adapter – No-Hub and Split Flange
| Size, in. | A, in. | J, in. |
| 2 | 53/4 | 6  |
| 3 | 7  | 71/2 |
| 4 | 8 | 9  |
Note 1: Flange dimensions are 150 lb ANSI standard.
Note 2: 1 in. = 25.4 mm.
FIG. 33 MJ to Lead Adapter
| Type  | Size, in. | B, in. | C, in. | D, in. |
|   AD-11 |   11/2 | 21/4 | 11/2 |    125/32 |
Note 1: 1 in. = 25.4 mm.
FIG. 34 Floor Drains
Note 1: 1 in. = 25.4 mm.
FIG. 35 Hub and Plain End Pipe
| Size, in. | A, in. | B, in. | C, in. | D, in. | E, in. | F, in. |
|    2 |  49/16 |   43/16 |   35/16 |   21/32 |   211/16 |   25/8 |
|    3 |  55/16 |   53/16 |   45/16 |   31/8 |   325/32 |   25/8 |
|    4 |  63/8 |   63/16 |   55/16 |   41/8 |   425/32 |   25/8 |
|    6 |  817/32 |   811/32 |   75/16 |   515/16 |   611/16 |   3 |
|    8 |  111/4 |   103/4 |   95/8 |   81/4 |   9 |   3 |
|   10 |  141/4 |   133/4 |   121/4 |   10 |   111/4 |   37/8 |
|   12 |  163/4 |   16 |   141/2 |   12 |   131/4 |   4 |
|   15 |  201/4 |   193/4 |   173/4 |   15 |   163/4 |   41/8 |
| Size, in. | t, in. | Weight, lb | Working | Overall Length |
|  2 |  5/16 | 0.31 | 7 |   7 ft 25/8 in. |
|  3 |  5/16 | 0.31 | 7 |   7 ft 25/8 in. |
|  4 |  5/16 | 0.31 | 7 |   7 ft 25/8 in. |
|  6 |  13/32 | 0.40 | 7 |   7 ft 3 in. |
|  8 |  13/32 | 0.40 | 7 |   7 ft 3 in. |
| 10 |  5/8 | 0.62 | 7 |   7 ft 37/8 in. |
| 12 |  5/8 | 0.62 | 5 |   5 ft 4 in. |
| 15 |  7/8 | 0.75 | 5 |   5 ft 41/8 in. |
Note 1: 1 in. = 25.4 mm.
FIG. 36 Straight Tees
| Size, in. | Weight, | A, in. | B, in. | C, in. |
|   2 × 11/2 |     11 |   81/2 |   17/8 |    65/8 |
|   2 × 2 |     12 |   9 |   2 |    7 |
|   3 × 2 |     17 |   9 |   21/2 |    613/16 |
|   3 × 3 |     19 |   10 |   21/2 |    71/2 |
|   4 × 2 |     20 |   9 |   3 |    7 |
|   4 × 3 |     221/2 |   10 |   3 |    71/4 |
|   4 × 4 |     26 |   11 |   3 |    8 |
Note 1: 1 in. = 25.4 mm.
FIG. 37 Sanitary T Branches
| Size, in. | Weight, lb | A, in. | B, in. | C, in. |
|   2 × 11/2 |   11 | 81/2 | 31/2 | 63/4 |
|    2 × 2 |   12 | 9 | 31/2 | 7 |
|    3 × 11/2 |   16 | 81/2 | 4 | 63/4 |
|    3 × 2 |   18 | 9 | 4 | 7 |
|    3 × 3 |   20 | 10 | 4 | 71/2 |
|    4 × 11/2 |   18 | 81/2 | 41/2 | 63/4 |
|    4 × 2 |   19 | 9 | 41/2 | 7 |
|    4 × 3 |   26 | 10 | 41/2 | 71/2 |
|    4 × 4 |   28 | 11 | 41/2 | 8 |
|    6 × 2 |   31 | 9 | 51/2 | 7 |
|    6 × 3 |   33 | 10 | 51/2 | 71/2 |
|    6 × 4 |   35 | 11 | 51/2 | 8 |
|    6 × 6 |   50 | 13 | 51/2 | 9 |
|    8 × 4 |   62 | 105/8 | 61/4 | 8 |
|    8 × 6 |   65 | 141/2 | 65/8 | 101/2 |
|    8 × 8 |  113 | 19 | 65/8 | 131/2 |
|   10 × 6 |  130 | 141/4 | 75/8 | 101/2 |
|   10 × 10 |  180 | 21 | 73/4 | 141/2 |
|   12 × 8 |  187 | 19 | 83/4 | 131/2 |
Note 1: 1 in. = 25.4 mm.
FIG. 38 Sanitary Y Branches
| Size, in. | Weight, lb  | A, in. | B, in. | C, in. |
|    2 × 11/2 |  11   | 85/8 | 43/8 | 43/8 |
|    2 × 2 |  12   | 9 | 41/4 | 43/4 |
|    3 × 11/2 |  16   | 85/8 | 51/16 | 37/8 |
|    3 × 2 |  17   | 9 | 5 | 43/16 |
|    3 × 3 |  21   | 101/2 | 51/2 | 5 |
|    4 × 11/2 |  17   | 91/8 | 513/16 | 37/8 |
|    4 × 2 |  21   | 9 | 53/4 | 311/16 |
|    4 × 3 |  26   | 101/2 | 61/4 | 41/2 |
|    4 × 4 |  30   | 12 | 63/4 | 51/4 |
|    6 × 2 |  28   | 9 | 71/8 | 211/16 |
|    6 × 3 |  35   | 101/2 | 75/8 | 31/2 |
|    6 × 4 |  45   | 121/4 | 81/4 | 41/4 |
|    6 × 6 |  60   | 143/4 | 91/8 | 53/4 |
|    8 × 2 |  60   | 167/8 | 9 | 41/2 |
|    8 × 3 |  63   | 121/8 | 9 | 33/4 |
|    8 × 4 |  65   | 131/2 | 10 | 41/2 |
|    8 × 6 |  79   | 161/2 | 11 | 61/16 |
|    8 × 8 | 117   | 191/2 | 121/4 | 71/4 |
|   10 × 4 | 160   | 131/2 | 111/2 | 31/2 |
|   10 × 6 | 165   | 165/8 | 131/2 | 37/8 |
|   10 × 8 | 170   | 193/4 | 143/8 | 43/8 |
|   10 × 10 | 180   | 221/2 | 15 | 75/8 |
|   12 × 4 | 173   | 181/4 | 153/16 | 41/2 |
|   12 × 6 | 196   | 181/4 | 161/2 | 41/2 |
|   12 × 8 | 200   | 233/8 | 151/2 | 5 |
|   12 × 10 | 275   | 27 | 191/2 | 6 |
|   12 × 12 | 288   | 251/2 | 183/8 | 71/4 |
|   15 × 15 | 455 | 321/8 | 223/4 | 81/8 |
Note 1: 1 in. = 25.4 mm.
FIG. 39 Double-Branch Sanitary Tee
FIG. 40 Double-Branch Sanitary Y
| Size, in. | Weight, lb | A, in. | B, in. | C, in. |
| 2 × 11/2 | 14 | 85/8 | 43/8 | 43/8 |
| 2 × 2 | 15 | 9 | 41/4 | 43/4 |
| 3 × 11/2 | 19 | 85/8 | 51/16 | 37/8 |
| 3 × 2 | 20 | 9 | 5 | 43/16 |
| 3 × 3 | 28 | 101/2 | 51/2 | 5 |
| 4 × 11/2 | 21 | 91/8 | 513/16 | 37/8 |
| 4 × 2 | 23 | 9 | 53/4 | 311/16 |
| 4 × 3 | 26 | 101/2 | 61/4 | 41/2 |
| 4 × 4 | 33 | 12 | 63/4 | 51/4 |
| 6 × 2 | 31 | 9 | 71/8 | 211/16 |
| 6 × 3 | 46 | 101/2 | 75/8 | 31/2 |
| 6 × 4 | 52 | 12 | 81/8 | 41/4 |
| 6 × 6 | 65 | 143/4 | 91/8 | 53/4 |
| 8 × 4 | 71 | 131/2 | 10 | 101/2 |
| 8 × 6 | 86 | 161/2 | 11 | 61/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 41 Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y)
| Size, in. | Weight, | A, in. | B and B, | C, in. | E, in. |
| 2 × 11/2 | 15  | 85/8 | 91/4 | 43/8 | 73/8 |
| 2 × 2 | 17  | 9 | 101/2 | 43/4 | 81/4 |
| 3 × 11/2 | 17  | 85/8 | 101/4 | 37/8 | 73/8 |
| 3 × 2 | 22  | 9 | 111/2 | 43/16 | 83/16 |
| 3 × 3 | 27  | 101/2 | 13 | 5 | 99/16 |
| 4 × 11/2 | 24  | 91/8 | 113/4 | 37/8 | 81/8 |
| 4 × 2 | 24  | 9 | 121/2 | 311/16 | 83/16 |
| 4 × 3 | 28  | 101/2 | 14 | 41/2 | 99/16 |
| 4 × 4 | 40  | 12 | 151/2 | 51/4 | 1013/16 |
| 6 × 3 | 45  | 101/2 | 16 | 31/2 | 99/16 |
| 6 × 4 | 57  | 12 | 171/2 | 41/4 | 1013/16 |
| 6 × 6 | 83  | 15 | 201/2 | 53/4 | 137/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 42 Short-Sweep Quarter Bends
| Size, in. | Weight, lb | B, in. | C, in. |
| 2 | 11 | 51/4 |  8 |
| 3 | 20 | 6  |  9 |
| 4 | 25 | 61/2 | 10 |
Note 1: 1 in. = 25.4 mm.
FIG. 43 Long-Sweep Quarter Bends
| Size, | Weight,   | B, | C, |
| 2 | 14   | 81/2 | 12 |
| 3 | 24   | 9 | 121/2 |
| 4 | 29   | 91/2 | 13 |
| 6 | 47   | 101/2 | 14 |
| 8 | 98 | 111/8 | 15 |
Note 1: 1 in. = 25.4 mm.
FIG. 44 Sanitary Combination Y and 1/8 Bend (T-Y)
| Size, | Weight, | A, | B, | C, | E, |
|  2 × 11/2 |  11 | 85/8 | 45/8 | 43/8 | 73/8 |
|  2 × 2 |  13 | 9 | 51/4 | 43/4 | 81/4 |
|  3 × 11/2 |  14 | 85/8 | 51/8 | 37/8 | 73/8 |
|  3 × 2 |  18 | 9 | 53/4 | 43/16 | 83/16 |
|  3 × 3 |  24 | 101/2 | 61/2 | 5 | 99/16 |
|  4 × 11/2 |  17 | 91/8 | 57/8 | 37/8 | 81/8 |
|  4 × 2 |  21 | 9 | 61/4 | 311/16 | 83/16 |
|  4 × 3 |  23 | 101/2 | 7 | 41/2 | 99/16 |
|  4 × 4 |  31 | 12 | 73/4 | 51/4 | 103/16 |
|  6 × 2 |  33 | 9 | 71/4 | 211/16 | 83/16 |
|  6 × 3 |  37 | 101/2 | 8 | 31/2 | 99/16 |
|  6 × 4 |  47 | 12 | 83/4 | 41/4 | 1013/16 |
|  6 × 6 |  63 | 15 | 101/4 | 53/4 | 137/16 |
| 10 × 6 | 185 | 163/4 | 121/2 | 47/16 | 43/8 |
| 10 × 8 | 192 | 213/8 | 151/8 | 61/2 | 181/2 |
Note 1: 1 in. = 25.4 mm.
FIG. 45 Quarter Bends
| Size, | Weight, | B, | C, |
| 2 |   9 | 31/2 | 7 |
| 3 |  16 | 4 | 71/2 |
| 4 |  20 | 41/2 | 8 |
| 6 |  36 | 51/2 | 9 |
| 8 |  54 | 61/8 | 10 |
| 10 | 116 | 85/8 | 12 |
| 12 | 195 | 103/8 | 14 |
Note 1: 1 in. = 25.4 mm.
FIG. 46 Sixth Bends
| Size, | Weight, |  B, |  C, |
| 2 |  8 | 21/4 | 53/4 |
| 3 | 11 | 21/2 | 6 |
| 4 | 15 | 23/16 | 65/16 |
| 6 | 27 | 33/8 | 67/8 |
| 8 | 71 | 41/8 | 9 |
Note 1: 1 in. = 25.4 mm.
FIG. 47 Eighth Bends
| Size, | Weight, | B, | C, |
|  2 |   7 | 13/4 | 51/4 |
|  3 |  13 | 115/16 | 57/16 |
|  4 |  16 | 23/16 | 511/16 |
|  6 |  25 | 29/16 | 61/16 |
|  8 |  46 | 311/16 | 813/16 |
| 10 |  95 | 41/4 | 91/4 |
| 12 | 132 | 5 | 95/8 |
Note 1: 1 in. = 25.4 mm.
FIG. 48 Sixteenth Bends
| Size, | Weight, |  B, |  C, |
| 2 |  6 | 11/8 | 45/8 |
| 3 |  8 | 13/16 | 411/16 |
| 4 | 11 | 15/16 | 413/16 |
| 6 | 21 | 11/2 | 5 |
| 8 | 44 | 21/16 | 71/8 |
| 10 | 80 | 2 | 67/8 |
Note 1: 1 in. = 25.4 mm.
FIG. 49 Sanitary Increasers
| Size, | Weight, | A, |
|     2 × 3 |  9 | 9 |
|     2 × 4 | 13 | 9 |
|     2 × 6 | 17 | 9 |
|     3 × 4 | 17 | 9 |
|     3 × 6 | 16 | 9 |
|     4 × 6 | 17 | 9 |
|     4 × 8 | 33 | 115/8 |
|     6 × 8 | 50 | 117/8 |
|     8 × 10 | 85 | 16 |
Note 1: 1 in. = 25.4 mm.
FIG. 50 Hub Strainers
| Size, | Weight, |
| 2 |         21/2 |
| 3 |         3 |
| 4 |         5 |
| 6 |         10 |
| 8 |         18 |
Note 1: 1 in. = 25.4 mm.
FIG. 51 Sanitary Reducers
| Size, | Weight, | A, in. | |
|
| 3 × 11/2 |  6 | 5 |
|
| 3 × 2 |  7 | 5 |
|
| 4 × 11/2 |  7 | 5 |
|
| 4 × 2 |  9 | 5 |
|
| 4 × 3 | 11 | 5 |
|
| 6 × 2 | 12 | 5 |
|
| 6 × 3 | 13 | 5 |
|
| 6 × 4 | 14 | 5 |
|
| 8 × 4 | 22 | 6 |
|
| 8 × 6 | 25 | 6 |
|
| 10 × 6 | 39 | 6 |
|
| 10 × 8 | 51 | 6 |
|
| 12 × 6 | 55 |  61/2 |
|
| 12 × 8 | 65 | 6 |
|
| 12 × 10 | 83 | 6 |
|
| 15 × 6 | 79 | 6 |
|
| 15 × 12 | 109  | 6 |
Note 1: 1 in. = 25.4 mm.
FIG. 52 Double Hubs
| Size, | Weight, | A, |
|  2 | 61/2 | 1 |
|  3 | 9  | 1 |
|  4 | 12 | 1 |
|  6 | 18 | 1 |
|  8 | 40 | 2 |
| 10 | 82 | 2 |
Note 1: 1 in. = 25.4 mm.
FIG. 53 Pipe Plugs
| Size, | Weight, |
|  2 |  2 |
|  3 |  3 |
|  4 |  5 |
|  6 | 10 |
|  8 | 17 |
| 12 | 56 |
Note 1: 1 in. = 25.4 mm.
FIG. 54 Cleanout Plugs
| Size, | Weight, |
|  2 | 31/2 |
|  3 | 61/2 |
|  4 | 11  |
|  6 | 14  |
|  8 | 26  |
| 10 | 39  |
Note 1: 1 in. = 25.4 mm.
FIG. 55 Adapter – Plain End and Split Flange
| Size, | Weight, | A, | J, |
| 2 |  5 |    53/4 |    6 |
| 3 | 11 |    7 |    71/2 |
| 4 | 12 |    8 |    9 |
| 6 | 22 |    91/2 |    11 |
| 8 | 44 |    103/4 |    131/2 |
Note 1: 1 in. = 25.4 mm.
FIG. 56 Adapter – Hub and Split Flange
| Size, | Weight, | A, | J, |
| 2 |  5 | 21/2 | 6  |
| 3 |  7 | 21/2 | 71/2   |
| 4 | 12 | 23/4 | 9  |
| 6 | 16 | 3   | 11   |
| 8 | 36 | 31/2 | 131/2 |
Note 1: 1 in. = 25.4 mm.
FIG. 57 Combination Cleanout and Test Tees
| Size, | Weight, | A, | B, |  C, | D, | E, | F, |
| 2 | 12 | 21/2   |  9 |  313/16 | 35/8 | 31/16 |  27/8 |
| 3 | 22 | 27/8   | 10 |  5 | 45/8 | 41/4   |  313/16 |
| 4 | 29 | 39/16 | 11 |  57/16 | 55/8 | 41/2   |  413/16 |
Note 1: 1 in. = 25.4 mm.
FIG. 58 Insertable Joints
| Plate No. | Size, | Weight, | A, | B, |
| 5045 | 2 | 11 | 73/4 | 61/2 |
| 5070 | 3 | 17 | 83/8 | 73/8 |
| 5095 | 4 | 21 | 91/8 | 77/8 |
| 5144 | 6 | 37 | 91/8 | 77/8 |
Note 1: 1 in. = 25.4 mm.
FIG. 59 Backwater Valves
| Size, in. |
| 3 |
| 4 |
| 6 |
| 8 |
Note 1: 1 in. = 25.4 mm.
FIG. 60 Sanitary P Traps
| Size, | Without | Hub | A, | B, | C, | D, | E, | G, | H, | Vent, |
| 2 | 12 | 16 | 11 | 3 | 61/4 | 41/2 | 21/4 |   313/16 |   15/8 | 2 |
| 3 | 25 | 32 | 121/2 | 41/4 | 61/4 | 51/2 | 3 |   41/2 |   25/16 | 3 |
| 4 | 37 | 45 | 14 | 51/2 | 7 | 61/2 | 31/4 |   53/16 |   3 | 4 |
| 6 | 68 | 80 | 17 | 81/2 | 8 | 81/2 | 4 |   61/2 |   315/16 | 4 |
Note 1: Depth of seal on all traps shall be 21/2 in.
Note 2: 1 in. = 25.4 mm.
FIG. 61 Sanitary S Traps
| Size, | Without | Hub | A, | B, | C, | D, | E, | F, | G, | H, | Vent, |
| 2 | 16 | 18 | 91/4   | 3 |  8 | 41/2 | 33/4 | 43/4 |   313/16 |   15/8 | 2 |
| 3 | 24 | 29 | 101/2 | 41/4 | 10 | 51/2 | 41/4 | 61/4 |   41/2 |   25/16 | 3 |
| 4 | 33 | 39 | 111/4 | 51/2 | 12 | 61/2 | 41/4 | 7 |   53/16 |   3 | 4 |
| 6 | 82 | 89 | 14 | 81/2 | 16 | 81/2 | 5 | 9 |   61/2 |   315/16 | 4 |
Note 1: Depth of seal on all traps shall be 21/2 in.
Note 2: 1 in. = 25.4 mm.
FIG. 62 Sanitary Running Traps
| Size, | Without | Single | Double | A, | B, | D, | E, | F, | G, | H, | Vent, |
|  2 |  14 |  17 |  22 | 131/2 | 21/2 | 41/2 | 21/2 | 51/4 |   85/16 |   15/8 | 2 |
|  3 |  29 |  36 |  42 | 151/2 | 3 | 51/2 | 31/4 | 61/4 |   10 |   25/16 | 3 |
|  4 |  41 |  49 |  57 | 171/2 | 31/2 | 61/2 | 31/2 | 71/4 |   1111/16 |   3 | 4 |
|  6 |  78 |  87 | 168 | 211/2 | 41/2 | 81/2 | 41/4 | 81/4 |   15 |   315/16 | 4 |
|  8 | 162 | 165 | 208 | 267/8 | 51/2 | 11 | 37/8 | 12 |   187/16 |   51/4 | 6 |
| 10 | 330 | 334 | 346 | 317/8 | 71/8 | 13 | 51/8 | 16 |   221/4 |   611/16 | 6 |
Note 1: Single hub vent is located on the inlet side. Depth of seal on 8- and 10-in. traps is 3 in. All others 21/2 in.
Note 2: 1 in. = 25.4 mm.
FIG. 63 Outside Caulk
| Plate | Outlet | Weight, lb |
| 1 | 2, 3, 4 and 6 | 45 |
| 2 | 2, 3, 4 and 6 | 45 |
| 3 | 2, 3, 4 and 6 | 53 |
| 4 | 2, 3, 4 and 6 | 53 |
| 5 | 2, 3, 4 and 6 | 41 |
| 6 | 2, 3, 4 and 6 | 42 |
| 7 | 2, 3, 4 and 6 | 48 |
| 8 | 2, 3, 4 and 6 | 49 |
Note 1: 1 in. = 25.4 mm.
FIG. 64 Outside Caulk with Basin
| Plate | Size, | A, | B, | C, |
| 5, 6, 7, 8 | 2 | 27/8 | 31/2 | 5/16 |
|
| 3 | 37/8 | 41/2 | 5/16 |
|
| 4 | 47/8 | 51/2 | 3/8   |
|
| 6 | 7 | 73/4 | 3/8 |
Note 1: 1 in. = 25.4 mm.
FIG. 65 Inside Caulk
Note 1: 1 in. = 25.4 mm.
FIG. 66 Floor Drains
| Plate | Outlet | Weight, lb |
| 1 | 3 | 70 |
| 2 | 4 | 73 |
| 3 | 2 | 37 |
| 4 | 2 | 45 |
| Plate | Size, | A, | B, | C, | D, | E, | F, |
| 1 | 3 | 8 | 9 | 57/8 | 11/2 | 14 | 141/2 |
Note 1: 1 in. = 25.4 mm.
FIG. 67 Method of Installation
FIG. 68 Floor Drain Funnel Attachment
Note 1: 1 in. = 25.4 mm.
FIG. 69 No. 1, 2, 3, 4, and 5 Overflows
| Plate | A, in.A | B, in.A | C, in. |
| 1 | 2 |  41/8 | 1 |
| 2 | 4 |  61/8 | 1 |
| 3 | 6 |  81/8 | 1 |
| 4 | 8 | 101/8 | 1 |
| 5 | 0 |  21/8 | 1 |
Note 1: 1 in. = 25.4 mm.
FIG. 70 Sink Outlet
| Plate | Size, | A, | B, | C, | D, | E, |
| 1 | 11/2 or 2 |  3/4 to 11/4 | 10 | 31/2 |   43/8 |   1/8 |
| 2 | 11/2 or 2 |  1 to 2 | 10 | 21/2 |   37/8 |   7/16 |
| 3 | 11/2 or 2 |  1 to 2 | 10 | 21/2 |   3 |   1/4 |
| 4 | 11/2 |  0 to 2 | 101/4 |
|   35/16 |   1/4 |
Note 1: Furnished with flat loose strainer plates.
Note 2: 1 in. = 25.4 mm.
FIG. 71 Detailed Cross Section of Cleanout
| Size, in. | Diameter | A, in. |
| Under 6 | 11/2 | 23/16 |
| 6 and over | 21/4 | 29/16 |
Note 1: Traps can be supplied without cleanouts, as shown in the figure.
Note 2: 1 in. = 25.4 mm.
1.4.1 Pipe:
1.4.1.1 No-Hub (MJ) (Fig. 1):
|
| Size (in.) | Length (ft) |
|
| 11/2 | 7 |
|
| 2 | 7 |
|
| 3 | 7 |
|
| 4 | 7 |
1.4.1.2 Hub/Plain End (Fig.35):
|
| Size (in.) | Length (ft) |
|
|  2 | 7 |
|
|  3 | 7 |
|
|  4 | 7 |
|
|  6 | 7 |
|
|  8 | 7 |
|
| 10 | 5 |
|
| 12 | 5 |
|
| 15 | 5 |
1.4.2 Fitting (No-Hub) (MJ):
|
| Figs. |
| Quarter Bends | 2 |
| Sixth Bends | 3 |
| Return Bends | 4 |
| Double-Branch Quarter Bend | 5 |
| Eighth Bends | 6 |
| Sixteenth Bends | 7 |
| Long-Sweep Quarter Bends | 8 |
| Sanitary Y Branches | 9 |
| Double-Branch Sanitary Y | 10 |
| Sanitary Combination Y and 1/8 Bend | 11 |
| Double-Branch Sanitary Combination Y and 1/8 Bend | 12 |
| Sanitary T Branches | 13 |
| Double Branch Sanitary T | 14 |
| Sanitary Running Traps | 15 |
| Sanitary P Traps | 16 |
| Swivel Trap P-Style, Short | 17 |
| Swivel Trap P-Style, Long | 18 |
| Swivel Trap S-Style, Long | 19 |
| Centrifugal Drum Trap P Swivel Type | 20 |
| Centrifugal Drum Trap S Swivel Type | 21 |
| Combination Cleanout and Test Tees | 22 |
| Coupling | 23 |
| Pipe Plugs | 24 |
| Cleanout Plugs | 25 |
| No-Hub (MJ) Adapter | 26 |
| Reducers-Increasers | 27 |
| Sink Outlet | 28 |
| Sink Overflows | 29 |
| Threaded Adapters | 30 |
| Trap Cleanout Details | 31 |
| No-Hub (MJ) Adapter | 32 |
| (MJ) (No-Hub) to Lead Adapter | 33 |
| Floor Drains | 34 |
1.4.3 Fitting (Hub/Plain End):
|
| Figs. |
| Hub Plain End Pipe | 35 |
| Straight Tees | 36 |
| Sanitary T Branches | 37 |
| Sanitary Y Branches | 38 |
| Double-Branch Sanitary Tee | 39 |
| Double-Branch Sanitary Y | 40 |
| Double-Branch Sanitary Combination Y and 1/8 Bend (T-Y) | 41 |
| Short-Sweep Quarter Bends | 42 |
| Long-Sweep Quarter Bends | 43 |
| Sanitary Combination Y and 1/8 Bend (T-Y) | 44 |
| Quarter Bends | 45 |
| Sixth Bends | 46 |
| Eighth Bends | 47 |
| Sixteenth Bends | 48 |
| Sanitary Increasers | 49 |
| Hub Strainers | 50 |
| Sanitary Reducers | 51 |
| Double Hubs | 52 |
| Pipe Plugs | 53 |
| Cleanout Plugs | 54 |
| Adapter – Plain end to Split Flange | 55 |
| Adapter – Hub to-Split Flange | 56 |
| Combination Cleanout and Test Tees | 57 |
| Insertable Joints | 58 |
| Backwater Valves | 59 |
| Sanitary P Traps | 60 |
| Sanitary S Traps | 61 |
| Sanitary Running Traps | 62 |
| Floor Drains | 63, 64, 65 |
| Floor Drains | 66 |
| Floor Drains/Installation – Funnel Attachment | 67, 68 |
| Overflow | 69 |
| Sink Outlet | 70 |
| Detailed Cross Section of Cleanout | 71 |
| Chemical Composition | Table 3 |
| Transverse Bend Test Minimum Requirements | Table S1.1 |
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
