ASTM B209M-14

Name: ASTM B209M-14
Brand: ASTM
SKU: astm-b209m-14

system ASTM 2021-06-21 10 PDF 600 0 2026-07-03 18:42

loading preview...

summary

Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric) (Withdrawn 2021)

description

Scope

1.1 This specification covers aluminum and aluminum alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 4, and in the following finishes:

(A) Limits are in mass percent maximum unless shown as a range or stated otherwise.

(B) Analysis shall be made for the elements for which limits are shown in this table.

(C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded to the nearest unit in the last right hand place of figures used in expressing the specified limit, in accordance with the Rounding Method of Practice E29.

(D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered non-conforming. The Total for Other Elements does not include elements shown in the footnotes with specific composition limits.

(E) Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.

(F) Vanadium 0.05 max. The total for other elements does not include vanadium.

(G) The aluminum content shall be calculated by subtracting from 100.00 % the sum of all metallic elements present in amounts of 0.010 % or more each, rounded to the second decimal before determining the sum.

(H) Composition of cladding alloy as applied during the course of manufacture. Samples from finished sheet or plate shall not be required to conform to these limits.

(I) Vanadium, 0.05–0.15, zirconium, 0.10–0.25.

(J) 0.05–0.25 Zr.

(K) Gallium 0.03 max, vanadium 0.05 max.

(L) 0.10–0.6 Mn + Cr.

(M) In case there is a discrepancy in the values listed in Table 1 with those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” shall be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets.

(A) To determine conformance to this specification, each value for tensile strength and for yield strength shall be rounded to the nearest 1 MPa and each value for elongation to the nearest 0.5 %, both in accordance with the Rounding Method of Practice E29.

(B) The basis for establishment of mechanical property limits is shown in Annex A1.

(D) Materials in either of these tempers, (H32 or H22), (H34 or H24), (H36 or H26), (H38 or H28), (H12 or H22), (H14 or H24), (H16 or H26), (H18 or H28), may be supplied at the option of the supplier, unless one is specifically excluded by the contract or purchase order. When ordered as H2X tempers, the maximum tensile strength and minimum yield strength do not apply. When H2X tempers are supplied instead of ordered H1X or H3X tempers, the supplied H2X temper material shall meet the respective H1X or H3X temper tensile property limits.

(E) Tests of F temper plate for tensile properties are not required.

(F) The tension test specimen from plate over 12.50 mm in thickness is machined from the core and does not include the cladding alloy.

(G) This material is subject to some recrystallization and an attendant loss of brightness.


Alloy	Temper	Specified Thickness, mm		Axis of Test Specimen	Tensile Strength, MPa		Yield Strength (0.2 % offset), MPa		Elongation,^C min, %
Alloy	Temper	over	through	Axis of Test Specimen	min	max	min	max	in 50 mm	in 5× Diameter
2124	T851^E	25.00	50.00	longitudinal	455	...	395	...	...	5
2124	T851^E			long transverse	455	...	395	...	...	4
2124	T851^E			short transverse	440^J	...	380^J	...	...	1
2124	T851^E	50.00	80.00	longitudinal	450	...	395	...	...	5
2124	T851^E			long transverse	450	...	395	...	...	3
2124	T851^E			short transverse	435	...	380	...	...	1
2124	T851^E	80.00	100.00	longitudinal	450	...	385	...	...	4
2124	T851^E			long transverse	450	...	385	...	...	3
2124	T851^E			short transverse	425	...	370	...	...	1
2124	T851^E	100.00	130.00	longitudinal	440	...	380	...	...	4
2124	T851^E			long transverse	440	...	380	...	...	3
2124	T851^E			short transverse	420	...	365	...	...	1
2124	T851^E	130.00	150.00	longitudinal	435	...	370	...	...	4
2124	T851^E			long transverse	435	...	370	...	...	3
2124	T851^E			short transverse	400	...	350	...	...	1


Alloy	Temper	Specified Thickness, mm		Tensile Strength, MPa		Yield Strength (0.2 % offset), MPa		Elongation,^C min, %
Alloy	Temper	over	through	min	max	min	max	in 50 mm	in 5× Diameter
2219	O	0.50	12.50	...	220	...	110	12	...
2219	O	12.50	50.00	...	220	...	110	...	10
2219	T31^K (flat sheet)	0.50	1.00	315	...	200	...	8	...
2219	T31^K (flat sheet)	1.00	6.30	315	...	195	...	10	...
2219	T351^E^,^H plate (formerly T31 plate)	6.30	12.50	315	...	195	...	10	...
2219	T351^E^,^H plate (formerly T31 plate)	12.50	50.00	315	...	195	...	...	9
2219	T351^E^,^H plate (formerly T31 plate)	50.00	80.00	305	...	195	...	...	9
2219	T351^E^,^H plate (formerly T31 plate)	80.00	100.00	290	...	185	...	...	8
2219	T351^E^,^H plate (formerly T31 plate)	100.00	130.00	275	...	180	...	...	8
2219	T351^E^,^H plate (formerly T31 plate)	130.00	150.00	270	...	170	...	...	7
2219	T37^K	0.50	1.00	340	...	260	...	6	...
2219	T37^K	1.00	12.50	340	...	255	...	6	...
2219	T37^K	12.50	60.00	340	...	255	...	...	5
2219	T37^K	60.00	80.00	325	...	250	...	...	5
2219	T37^K	80.00	100.00	310	...	240	...	...	4
2219	T37^K	100.00	120.00	295	...	235	...	...	3
2219	T62^F	0.50	1.00	370	...	250	...	6	...
2219	T62^F	1.00	6.30	370	...	250	...	7	...
2219	T62^F	6.30	12.50	370	...	250	...	8	...
2219	T62^F	12.50	25.00	370	...	250	...	...	7
2219	T62^F	25.00	50.00	370	...	250	...	...	6
2219	T81 sheet	0.50	1.00	425	...	315	...	6	...
2219	T81 sheet	1.00	6.30	425	...	315	...	7	...
2219	T851^E (formerly T81 plate)	6.30	12.50	425	...	315	...	8	...
2219	T851^E (formerly T81 plate)	12.50	25.00	425	...	315	...	...	7
2219	T851^E (formerly T81 plate)	25.00	50.00	425	...	315	...	...	6
2219	T851^E (formerly T81 plate)	50.00	80.00	425	...	310	...	...	5
2219	T851^E (formerly T81 plate)	80.00	100.00	415	...	305	...	...	4
2219	T851^E (formerly T81 plate)	100.00	130.00	405	...	295	...	...	4
2219	T851^E (formerly T81 plate)	130.00	150.00	395	...	290	...	...	3
2219	T87	0.50	1.00	440	...	360	...	5	...
2219	T87	1.00	6.30	440	...	360	...	6	...
2219	T87	6.30	12.50	440	...	350	...	7	...
2219	T87	12.50	25.00	440	...	350	...	...	6
2219	T87	25.00	80.00	440	...	350	...	...	5
2219	T87	80.00	100.00	425	...	345	...	...	3
2219	T87	100.00	120.00	420	...	340	...	...	2
2219	F^G	6.30	50.00	...	...	...	...	...	...


Alclad 2219	O	0.50	1.00	...	220	...	110	12	...
Alclad 2219	O	1.00	2.50	...	220	...	110	12	...
Alclad 2219	O	2.50	12.50	...	220	...	110	12	...
Alclad 2219	O	12.50	50.00	...	220^H	...	110^H	...	10
Alclad 2219	T31^K (flat sheet)	1.00	2.50	290	...	170	...	10	...
Alclad 2219	T31^K (flat sheet)	2.50	6.30	305	...	180	...	10	...
Alclad 2219	T351^E^,^K plate (formerly T31 plate)	6.30	12.50	305	...	180	...	10	...
Alclad 2219	T37^K	1.00	2.50	310	...	235	...	6	...
Alclad 2219	T37^K	2.50	12.50	325	...	240	...	6	...
Alclad 2219	T62^F	0.50	1.00	305	...	200	...	6	...
Alclad 2219	T62^F	1.00	2.50	340	...	220	...	7	...
Alclad 2219	T62^F	2.50	6.30	350	...	235	...	7	...
Alclad 2219	T62^F	6.30	12.50	350	...	235	...	8	...
Alclad 2219	T62^F	12.50	25.00	370^H	...	250^H	...	...	7
Alclad 2219	T62^F	25.00	50.00	370^H	...	250^H	...	...	6
Alclad 2219	T81 (flat sheet)	0.50	1.00	340	...	255	...	6	...
Alclad 2219	T81 (flat sheet)	1.00	2.50	380	...	285	...	7	...
Alclad 2219	T81 (flat sheet)	2.50	6.30	400	...	295	...	7	...
Alclad 2219	T851^E plate (formerly T81 plate)	6.30	12.50	400	...	290	...	8	...
Alclad 2219	T87	1.00	2.50	395	...	315	...	6	...
Alclad 2219	T87	2.50	6.30	415	...	330	...	6	...
Alclad 2219	T87	6.30	12.50	415	...	330	...	7	...
Alclad 2219	F^G	6.30	50.00	...	...	...	...	...	...


6013	T4	0.50	6.30	275	...	145	...	20	...
6013	T6	0.50	6.30	360	...	315	...	8	...
6013	T651^E	6.30	40.00	365	...	305	...	...	4
6013	T651^E	40.00	80.00	370	...	325	...	...	4
6013	T651^E	80.00	160.00	380	...	325	...	...	3


6061	O	0.15	0.20	...	150	...	85	10	...
6061	O	0.20	0.25	...	150	...	85	12	...
6061	O	0.25	0.50	...	150	...	85	14	...
6061	O	0.50	3.20	...	150	...	85	16	...
6061	O	3.20	12.50	...	150	...	85	18	...
6061	O	12.50	25.00	...	150	...	...	...	16
6061	O	25.00	80.00	...	150	...	...	...	14
6061	T4	0.15	0.20	205	...	110	...	10	...
6061	T4	0.20	0.25	205	...	110	...	12	...
6061	T4	0.25	0.50	205	...	110	...	14	...
6061	T4	0.50	6.30	205	...	110	...	16	...
6061	T451^E	6.30	12.50	205	...	110	...	18	...
6061	T451^E	12.50	25.00	205	...	110	...	...	16
6061	T451^E	25.00	80.00	205	...	110	...	...	14
6061	T42^F	0.15	0.20	205	...	95	...	10	...
6061	T42^F	0.20	0.25	205	...	95	...	12	...
6061	T42^F	0.25	0.50	205	...	95	...	14	...
6061	T42^F	0.50	6.30	205	...	95	...	16	...
6061	T42^F	6.30	12.50	205	...	95	...	18	...
6061	T42^F	12.50	25.00	205	...	95	...	...	16
6061	T42^F	25.00	80.00	205	...	95	...	...	14
6061	T6, T62^F	0.15	0.20	290	...	240	...	4	...
6061	T6, T62^F	0.20	0.25	290	...	240	...	6	...
6061	T6, T62^F	0.25	0.50	290	...	240	...	8	...
6061	T6, T62^F	0.50	6.30	290	...	240	...	10	...
6061	T62^F, T651^E	6.30	12.50	290	...	240	...	10	...
6061	T62^F, T651^E	12.50	25.00	290	...	240	...	...	8
6061	T62^F, T651^E	25.00	50.00	290	...	240	...	...	7
6061	T62^F, T651^E	50.00	100.00	290	...	240	...	...	5
6061	T62^F, T651^E	100.00	150.00^L	275	...	240	...	...	5
6061	F^G	6.30	80.00	...	...	...	...	...	...


Alclad 6061	O	0.24	0.50	...	140	...	85	14	...
Alclad 6061	O	0.50	3.20	...	140	...	85	16	...
Alclad 6061	O	3.20	12.50	...	140	...	85	18	...
Alclad 6061	O	12.50	25.00	...	150^H	...	...	...	16
Alclad 6061	O	25.00	80.00	...	150^H	...	...	...	14
Alclad 6061	T4	0.24	0.50	185	...	95	...	14	...
Alclad 6061	T4	0.50	6.30	185	...	95	...	16	...
Alclad 6061	T451^E	6.30	12.50	185	...	95	...	18	...
Alclad 6061	T451^E	12.50	25.00	205^H	...	110^H	...	...	16
Alclad 6061	T451^E	25.00	80.00	205^H	...	110^H	...	...	14
Alclad 6061	T42^F	0.24	0.50	185	...	85	...	14	...
Alclad 6061	T42^F	0.50	6.30	185	...	85	...	16	...
Alclad 6061	T42^F	6.30	12.50	185	...	85	...	18	...
Alclad 6061	T42^F	12.50	25.00	205^H	...	95^H	...	...	16
Alclad 6061	T42^F	25.00	80.00	205^H	...	95^H	...	...	14
Alclad 6061	T6, T62^F	0.24	0.50	260	...	220	...	8	...
Alclad 6061	T6, T62^F	0.50	6.30	260	...	220	...	10	...
Alclad 6061	T62^F, T651^E	6.30	12.50	260	...	220	...	10	...
Alclad 6061	T62^F, T651^E	12.50	25.00	290^H	...	240^H	...	...	8
Alclad 6061	T62^F, T651^E	25.00	50.00	290^H	...	240^H	...	...	7
Alclad 6061	T62^F, T651^E	50.00	100.00	290^H	...	240^H	...	...	5
Alclad 6061	T62^F, T651^E	100.00	120.00^L	275^H	...	240^H	...	...	5
Alclad 6061	F^G	6.30	80.00	...	...	...	...	...	...


7075	O	0.39	12.50	...	275	...	145	10	...
7075	O	12.50	50.00	...	275	...	...	...	9
7075	T6, T62^F	0.19	0.32	510	...	435	...	5	...
7075	T6, T62^F	0.32	1.00	525	...	460	...	8	...
7075	T6, T62^F	1.00	3.20	540	...	470	...	9	...
7075	T6, T62^F	3.20	4.70	545	...	475	...	9	...
7075	T6, T62^F	4.70	6.30	550	...	475	...	9	...
7075	T62^F, T651^E	6.30	12.50	540	...	460	...	9	...
7075	T62^F, T651^E	12.50	25.00	540	...	470	...	...	6
7075	T62^F, T651^E	25.00	50.00	530	...	460	...	...	5
7075	T62^F, T651^E	50.00	60.00	525	...	440	...	...	4
7075	T62^F, T651^E	60.00	80.00	495	...	420	...	...	4
7075	T62^F, T651^E	80.00	90.00	490	...	400	...	...	4
7075	T62^F, T651^E	90.00	100.00	460	...	370	...	...	2
7075	T73 sheet	1.00	6.30	460	...	385	...	8	...
7075	T7351^E plate	6.30	12.50	475	...	390	...	7	...
7075	T7351^E plate	12.50	25.00	475	...	390	...	...	6
7075	T7351^E plate	25.00	50.00	475	...	390	...	...	5
7075	T7351^E plate	50.00	60.00	455	...	360	...	...	5
7075	T7351^E plate	60.00	80.00	440	...	340	...	...	5
7075	T7351^E plate	80.00	90.00	435	...	340	...	...	5
7075	T7351^E plate	90.00	100.00	420	...	330	...	...	5
7075	T76 sheet	1.60	6.30	505	...	425	...	8	...
7075	T7651^E plate	6.30	12.50	495	...	420	...	8	...
7075	T7651^E plate	12.50	25.00	490	...	415	...	...	5
7075	F^G	6.30	100.00	...	...	...	...	...	...


Alclad 7075	O	0.19	0.40	...	250	...	140	9	...
Alclad 7075	O	0.40	1.60	...	250	...	140	10	...
Alclad 7075	O	1.60	4.00	...	260	...	140	10	...
Alclad 7075	O	4.00	12.50	...	270	...	145	10	...
Alclad 7075	O	12.50	25.00	...	275^H	...	...	...	9
Alclad 7075	T6, T62^F	0.19	0.32	470	...	400	...	5	...
Alclad 7075	T6, T62^F	0.32	1.00	490	...	420	...	8	...
Alclad 7075	T6, T62^F	1.00	1.60	495	...	425	...	9	...
Alclad 7075	T6, T62^F	1.60	3.20	510	...	440	...	9	...
Alclad 7075	T6, T62^F	3.20	4.70	510	...	440	...	9	...
Alclad 7075	T6, T62^F	4.70	6.30	525	...	450	...	9	...
Alclad 7075	T62^F, T651^E	6.30	12.50	515	...	445^H	...	9	...
Alclad 7075	T62^F, T651^E	12.50	25.00	540^H	...	470^H	...	...	6
Alclad 7075	T62^F, T651^E	25.00	50.00	530^H	...	460^H	...	...	5
Alclad 7075	T62^F, T651^E	50.00	60.00	525^H	...	440^H	...	...	4
Alclad 7075	T62^F, T651^E	60.00	80.00	495^H	...	420^H	...	...	4
Alclad 7075	T62^F, T651^E	80.00	90.00	490^H	...	400^H	...	...	4
Alclad 7075	T62^F, T651^E	90.00	100.00	460^H	...	370^H	...	...	2
Alclad 7075	T76 sheet	1.00	1.60	460	...	385	...	8	...
Alclad 7075	T76 sheet	1.60	4.70	470	...	395	...	8	...
Alclad 7075	T76 sheet	4.70	6.30	485	...	405	...	8	...
Alclad 7075	T7651^E plate	6.30	12.50	475	...	400	...	8	...
Alclad 7075	T7651^E plate	12.50	25.00	490^H	...	415^H	...	...	5
Alclad 7075	F^G	6.30	100.00	...	...	...	...	...	...


Alclad 1-Side 7075	O	0.39	1.60	...	260	...	145	10	...
Alclad 1-Side 7075	O	1.60	4.00	...	270	...	145	10	...
Alclad 1-Side 7075	O	4.00	12.50	...	270	...	145	10	...
Alclad 1-Side 7075	O	12.50	25.00	...	275^H	...	...	...	9
Alclad 1-Side 7075	T6, T62^F	0.19	0.32	490	...	415	...	5	...
Alclad 1-Side 7075	T6, T62^F	0.32	1.00	510	...	440	...	8	...
Alclad 1-Side 7075	T6, T62^F	1.00	1.60	515	...	450	...	9	...
Alclad 1-Side 7075	T6, T62^F	1.60	3.20	525	...	455	...	9	...
Alclad 1-Side 7075	T6, T62^F	3.20	4.70	530	...	460	...	9	...
Alclad 1-Side 7075	T6, T62^F	4.70	6.30	540	...	460	...	9	...
Alclad 1-Side 7075	T62^F, T651^E	6.30	12.50	525	....	455	...	9	...
Alclad 1-Side 7075	T62^F, T651^E	12.50	25.00	540^H	...	470^H	...	...	6
Alclad 1-Side 7075	T62^F, T651^E	25.00	50.00	530^H	...	460^H	...	...	5
Alclad 1-Side 7075	F^G	6.30	50.00	...	...	...	...	...	...

(A) To determine conformance to this specification, each value for tensile strength shall be rounded to the nearest 1 MPa and each value for elongation to the nearest 0.5 %, both in accordance with the Rounding Method of Practice E29.

(B) The basis for establishment of mechanical property limits is shown in Annex AI.

(D) Coiled sheet.

(E) For stress-relieved tempers (T351, T451, T651, T7351, T7651, and T851), characteristics and properties other than those specified may differ somewhat from the corresponding characteristics and properties of material in the basic temper.

(F) Material in the T42, T62, and T72 tempers is not available from the material producer.

(G) Test for tensile properties in the F temper are not required.

(H) The tension test specimen from plate over 12.50 mm in thickness is machined from the core and does not include the cladding.

(I) The T72 temper is applicable only to Alloys 2024 and Alclad 2024 sheet solution heat treated and artificially overaged by the user to develop increased resistance to stress-corrosion cracking.

(J) Short transverse tensile properties are not applicable to material less than 40 mm in thickness.

(K) Use of Alloys 2219 and Alclad 2219 in the T31, T351, and T37 tempers for finished products is not recommended.

(L) The properties for this thickness apply only to the T651 temper.

1.1.1 Plate in all alloys and sheet in heat-treatable alloys: mill finish.

1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish.

1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System (UNS) alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.

Note 1: Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy.

Note 2: See Specification B632/B632M for Tread Plate.

Note 3: See Specification B928/B928M for 5xxx-H116 and 5xxx-H321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in Specification B209, which do not require the additional corrosion testing/capability called out in Specification B928/B928M, may be suitable for marine and similar environment applications.

1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

1.4 This specification is the SI companion to Specification B209.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Details

Publisher ASTM

File size 158.83 KB

Pages 26

Format PDF

Publication date 2021-06-21

Download with Points

Rating ★★★★★

Points 600

File size 158.83 KB

Pages 26

Format PDF

Publication date 2021-06-21

ASTM B209M-14

Related Products