Documents Share & AVA Documents Free Downloads of Technical Documents, Standards, Industry Codes, and Regulations
Documents Documents Document Sharing Hub

    ASTM C400-98(2013)

    system ASTM 2018-01-01 11 PDF 370 0 2026-07-03 19:33
    summary
    Standard Test Methods for Quicklime and Hydrated Lime for Neutralization of Waste Acid
    description

    Significance and Use

    4.1 Since all limes and waste acid solutions are different, this test method evaluates the relative quantity of a given lime needed for the neutralization of a specific quantity of acid.

    4.2 Liming materials have a specific basicity factor or measure of alkalinity which can be used for comparing their relative neutralizing power. It avoids dependence on chemical analysis and is determined as grams of calcium oxide equivalents per kilogram of liming material.

    4.3 Likewise, specific waste acids have an acid value that can be expressed as grams of hydrochloric acid equivalent per litre of acid waste. This value is related on a stoichiometric basis to lime neutralization requirements of a liquid acid waste.

    Scope

    1.1 This test method covers the testing of quicklime and hydrated lime for use in the treatment of waste acid solutions and includes the characterization of the liming material and of the acid waste.

    Note 1—When agreed upon by the manufacturer and the purchaser, this method may be used directly to evaluate the lime requirement for a plant waste acid and in the preparation of the lime slurry; the pH, the time, temperature, and other conditions of treatment may be adjusted to conform to plant practice. Otherwise the test shall be performed as described in this method.
    Note 2—Under some conditions of test the lime requirement may vary substantially from that indicated by ultimate chemical analysis or by the use of a determination of available alkalinity by titration to a stoichiometric end point.

    1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Details
    Publisher ASTM
    File size 52.88 KB
    Pages 3
    Format PDF
    Publication date 2018-01-01

    Related Products

    More
    ★★★★★ ASTM A6/A6M-01 ASTM A6/A6M-01 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling ★★★★★ ASTM A20/A20M-01 ASTM A20/A20M-01 Standard Specification for General Requirements for Steel Plates for Pressure Vessels ★★★★★ ASTM D4328-18 ASTM D4328-18 Standard Practice for Calculation of Supersaturation of Barium Sulfate, Strontium Sulfate, and Calcium Sulfate Dihydrate (Gypsum) in Brackish Water, Seawater, and Brines ★★★★★ ASTM D4330-94(2002) ASTM D4330-94(2002) Standard Practice for Evaluation of Fiberglass Boat Polish and Wax ★★★★★ ASTM D6954-24 ASTM D6954-24 Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation ★★★★★ ASTM D653-26a Standard Terminology Relating to Soil, Rock, and Contained Fluids ASTM D653-26a Standard Terminology Relating to Soil, Rock, and Contained Fluids This ASTM terminology standard defines terms used in soil, rock, groundwater, grouting, geotechnical engineering, and related Committee D18 standards. ★★★★★ ASTM D613-26 Standard Test Method for Cetane Number of Diesel Fuel Oil ASTM D613-26 Standard Test Method for Cetane Number of Diesel Fuel Oil This standard establishes a test method for determining the cetane number of diesel fuel oil using a standardized single-cylinder, four-stroke-cycle, variable-compression-ratio diesel engine. ★★★★★ ASTM D1003-21 ASTM D1003-21 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics ★★★★★ ASTM D3363-22 ASTM D3363-22 Standard Test Method for Film Hardness by Pencil Test ★★★★★ ASTM D5329-16 ASTM D5329-16 Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements ★★★★★ ASTM D7283-17 ASTM D7283-17 Standard Test Method for Alpha and Beta Activity in Water By Liquid Scintillation Counting ★★★★★ Standard Test Method for the Sieve Analysis of Coke Standard Test Method for the Sieve Analysis of Coke This test method determines the size distribution of coke by separating a sample into defined sieve fractions and reporting each fraction as a percentage of the gross sample mass. ★★★★★ ASTM E29-06b ASTM E29-06b Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications ★★★★★ ASTM D5329-15 ASTM D5329-15 Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements ★★★★★ ASTM D4329-21 ASTM D4329-21 Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics