Documents Share & AVA Documents Free Downloads of Technical Documents, Standards, Industry Codes, and Regulations
Documents Documents Document Sharing Hub

    ASTM D2525-13

    system ASTM 2022-01-13 14 PDF 346 0 2026-07-03 21:49
    summary
    Standard Practice for Sampling Wool for Moisture (Withdrawn 2022)
    description

    Significance and Use

    5.1 This recommended practice furnishes directions for the sampling of wool of the various forms indicated in Section 1, in order that correct probability statements may be made about the relationship between the sample mean and the population mean. If these statements are to be correct, certain conditions, which are stated, must hold.

    5.2 This recommended practice requires that a deliberate act of randomization be performed so that all potential sampling units have approximately the same chance of being taken and no sampling unit is deprived of its chance of being taken.

    5.3 In any case where insufficient information about the variability of the sampling units within the lot is available, directions are given for calculating confidence limits for the sample mean so that a correct probability statement can still be made.

    Scope

    1.1 This practice covers the design of a sampling plan to be used to obtain samples for the determination of the moisture content of grease wool, scoured wool, carded wool, garnetted wool, wool top and intermediate products, and rovings.

    1.2 Directions are given for the designation of sampling units, calculation of the number of sampling units required to achieve a preselected precision and confidence level or, alternatively, for calculating the confidence limits for the mean based on the variability of the sample tested.

    Note 1—This practice for devising a sampling plan is intended for use in connection with Test Method D1576 or Test Method D2462. The sampling of raw wool for the determination of clean wool fiber present is covered in Practice D1060.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Details
    Publisher ASTM
    File size 66.08 KB
    Pages 5
    Format PDF
    Publication date 2022-01-13

    Related Products

    More
    ★★★★★ ASTM A6/A6M-01 ASTM A6/A6M-01 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling ★★★★★ ASTM A20/A20M-01 ASTM A20/A20M-01 Standard Specification for General Requirements for Steel Plates for Pressure Vessels ★★★★★ ASTM D4328-18 ASTM D4328-18 Standard Practice for Calculation of Supersaturation of Barium Sulfate, Strontium Sulfate, and Calcium Sulfate Dihydrate (Gypsum) in Brackish Water, Seawater, and Brines ★★★★★ ASTM D4330-94(2002) ASTM D4330-94(2002) Standard Practice for Evaluation of Fiberglass Boat Polish and Wax ★★★★★ ASTM D6954-24 ASTM D6954-24 Standard Guide for Exposing and Testing Plastics that Degrade in the Environment by a Combination of Oxidation and Biodegradation ★★★★★ ASTM D1003-21 ASTM D1003-21 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics ★★★★★ ASTM D3363-22 ASTM D3363-22 Standard Test Method for Film Hardness by Pencil Test ★★★★★ ASTM D653-26a Standard Terminology Relating to Soil, Rock, and Contained Fluids ASTM D653-26a Standard Terminology Relating to Soil, Rock, and Contained Fluids This ASTM terminology standard defines terms used in soil, rock, groundwater, grouting, geotechnical engineering, and related Committee D18 standards. ★★★★★ ASTM D613-26 Standard Test Method for Cetane Number of Diesel Fuel Oil ASTM D613-26 Standard Test Method for Cetane Number of Diesel Fuel Oil This standard establishes a test method for determining the cetane number of diesel fuel oil using a standardized single-cylinder, four-stroke-cycle, variable-compression-ratio diesel engine. ★★★★★ ASTM D5329-16 ASTM D5329-16 Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements ★★★★★ ASTM D5329-15 ASTM D5329-15 Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements ★★★★★ ASTM E29-06b ASTM E29-06b Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications ★★★★★ Standard Test Method for the Sieve Analysis of Coke Standard Test Method for the Sieve Analysis of Coke This test method determines the size distribution of coke by separating a sample into defined sieve fractions and reporting each fraction as a percentage of the gross sample mass. ★★★★★ ASTM D7283-17 ASTM D7283-17 Standard Test Method for Alpha and Beta Activity in Water By Liquid Scintillation Counting ★★★★★ ASTM D4329-21 ASTM D4329-21 Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics