ASTM F1667-11ae1 - Page 2

1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1.

Note 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3-67.

1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.

1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Classification and Identification Index

Type	Style		Style Identification	Table
INails (NL)	1.	Brads	BR	3
	2.	Barrel	BL	4
	3.	Boat	BTH/BTL	5
	4.	Box A	BXA	6
		Box B	BXB	7
	5.	Broom	BM	8
	6.	Casing	CN	9
	7.	Cooler	CL	10
	8.	Sinker	SK	11
	9.	Corker	CK	12
	10.	Common	CMA	13
		Common	CMC	14
		Common	CMS	15
		Common	CMM	16
	11.	Concrete	CTS/CTM	17
	12.	Double-headed	DH	18
	13.	Fine	FN	19
	14.	Finishing	FH	20
	15.	Flooring	FL	21
	16.	Lath	LHF	22
		Lath	LHH	23
	17.	Masonry	MR/MRH	24
	18.	Pallet	PL	25
	19.	Gypsum wallboard	GWS	26
		Gypsum wallboard	GWM	27
	20.	Roofing	RFA	28
		Roofing	RFS	29
		Roofing	RFC	30
		Roofing	RFL	31
		Roofing	RFR	32
		Roofing	RFD	33
		Roofing	RFNS/RFND	34
	21.	Shingle	SHAD/SHAS	35
		Shingle	SHSS/SHNSB	36
	22.	Siding	SDF/SDC/SDK	37
	23.	Slating	SLA/SLC/SLS	38
	24.	Rubber heel	RH	39
	25.	Underlayment	UL	40
	26.	Square-barbed	SB	41
	27.	Masonry drive	MD	42
	28.	Escutcheon	ES	43
	29.	Glulam rivet	GR	44
	30.	Post frame	PF	45
IICut nails (CN)	1.	Common	CM	46
	2.	Basket	BK	47
	3.	Clout	CL	48
	4.	Trunk	TR	49
	5.	Cobblers	CB	50
	6.	Extra-iron clinching	EC	51
	7.	Hob	HB	52
IIISpikes (SP)	1.	Common	CM	53
	2.	Gutter	GRF/GRO	54
	3.	Round	RDC/RDF	55
	4.	Barge and boat	BB	56
IVStaples (ST)	1.	Fence	FN	57
	2.	Poultry netting	PN	58
	3.	Flat top crown	FC	59
		Flat top crown	FCC	60
	4.	Round or V crown	RC	61
	5.	Preformed	PC	62
	6.	Electrical	RE	63
	7.	Preformed hoop	PH	64
	8.	Cap	STC	65

TABLE 2 Bend Angles for Fasteners Using the Test Methods F680 Bend Test

	Fastener Material	Bend Angle, °
1.	Steel wire: (low-carbon, medium-low carbon, medium-carbon) (unhardened)	180
2.	Stainless steel wire	180
3.	Hardened steel fasteners	20
4.	Sheet steel for cut nails, Type II, and cut spikes, Type III	90
5.	Copper (min 98 %)	180
6.	Copper clad wire (min 20 %)	180
7.	Aluminum alloy wire	90
8.	Brass wire	180

TABLE 3 Type I, Style 1Brads^A

Note—Steel wire, brad head, diamond point, round smooth shank, bright finish. When specified, brads shall have a modified brad head with a blunt or chiseled point for use with mechanical drivers.

TABLE 4 Type I, Style 2Barrel Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, bright, zinc or cement coated as specified.

TABLE 5 Type I, Style 3Boat nails^A

Note—Steel wire, oval countersunk head, chisel point, round smooth shank, bright or zinc coated as specified.

TABLE 6 Type I, Style 4ABox Nails^A

Note—Steel wire, flat head, diamond point, round, barbed or smooth shank, bright or cement coated as specified. When specified, box nails shall have an altered or T-head with a diamond, blunt, or chisel point for use with mechanical drivers.

TABLE 7 Type I, Style 4BBox Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, cement coated.

TABLE 8 Type I, Style 5Broom Nails^A

Note—Steel wire, flat or star head, diamond point, round smooth shank, bright finish, as specified.

TABLE 9 Type I, Style 6Casing Nails^A

Note—Steel wire, flat countersunk cupped head, diamond point, round smooth shank, bright finish.

TABLE 10 Type I, Style 7Cooler Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, cement coated. When specified, coolers shall have an altered or T-head for use with mechanical drivers.

TABLE 11 Type I, Style 8Sinker Nails^A

Note—Steel wire, flat countersunk head, diamond point, round smooth shank, bright or cement coated. When specified, sinkers shall have an altered or T-head for use with mechanical drivers.

TABLE 12 Type I, Style 9Corker Nails^A

Note—Steel wire, flat countersunk head, diamond point, round smooth shank, cement coated. When specified, corkers shall have an altered or T-head for use with mechanical drivers.

TABLE 13 Type I, Style 10Common Nails^A

Note—Aluminum alloy wire, flat head, diamond point, round smooth shank, or, when specified, square barbed shank.

TABLE 14 Type I, Style 10Common Nails^A

Note—Copper wire, flat head, diamond point, round smooth shank.

TABLE 15 Type I, Style 10Common Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, bright, zinc or cement coated as specified.

TABLE 16 Type I, Style 10Common Nails^A

Note—Aluminum alloy wire, stainless steel or steel wire, (bright, zinc coated or cement coated), altered or T-head, diamond or chisel point, round smooth or deformed shank, as specified. For use with mechanical drivers.

F1667 NLCMM
Dash No.	L	D	Dash No.	L	D	Dash No.	L	D	Dash No.	L	D	Dash No.	L	D	Dash No.	L	D
01	1 ¼	0.080	15	1 ¾	0.086	29	2	0.148	43	1 ¾	0.120	57	23/8	0.113	71	3	0.131
02	1 ¼	0.086	16	1 ¾	0.092	30	2 ¼	0.092	44	17/8	0.120	58	23/8	0.120	72	3	0.148
03	1 ¼	0.092	17	1 ¾	0.099	31	2 ¼	0.099	45	17/8	0.131	59	23/8	0.131	73	3 ¼	0.120
04	1 ¼	0.099	18	1 ¾	0.113	32	2 ¼	0.113	46	17/8	0.148	60	23/8	0.148	74	3 ¼	0.131
05	1 ½	0.080	19	17/8	0.080	33	2 ½	0.092	47	2	0.120	61	2 ½	0.120	75	3 ¼	0.148
06	1 ½	0.086	20	17/8	0.086	34	2 ½	0.099	48	2	0.131	62	2 ½	0.148	76	3 ½	0.135
07	1 ½	0.092	21	17/8	0.092	35	2 ½	0.113	49	21/8	0.099	63	2 ½	0.162	77	3 ½	0.148
08	1 ½	0.099	22	17/8	0.099	36	2 ½	0.131	50	21/8	0.113	64	25/8	0.148	78	3 ½	0.162
09	1 ½	0.113	23	17/8	0.113	37	3 ½	0.131	51	21/8	0.120	65	2 ¾	0.120	79	4	0.148
10	15/8	0.080	24	2	0.080	38	1 ½	0.120	52	21/8	0.131	66	2 ¾	0.131	80	4	0.162
11	15/8	0.086	25	2	0.086	39	1 ½	0.131	53	21/8	0.148	67	2 ¾	0.148	81	4 ½	0.148
12	15/8	0.092	26	2	0.092	40	1 ½	0.148	54	2 ¼	0.120	68	27/8	0.120	82	4 ½	0.162
13	15/8	0.099	27	2	0.099	41	1 ½	0.162	55	2 ¼	0.131	69	3	0.120	...	...	...
14	1 ¾	0.080	28	2	0.113	42	15/8	0.113	56	2 ¼	0.148	70	3	0.128	...	...	...

TABLE 17 Type I, Style 11Concrete Nails^A

Note—Harded steel, flat countersunk head, diamond point, smooth or mechanically deformed shank formed from round or square stock, as specified, bright finish.

TABLE 18 Type I, Style 12Double-Headed Nails^A

Note—Steel wire, flat heads, diamond point, round smooth shank, bright finish or cement coated.

TABLE 19 Type I, Style 13Fine Nails^A

Note—Steel or copper wire, flat head, diamond point, round smooth shank, bright finish.

TABLE 20 Type I, Style 14Finish Nails^A

Note—Steel wire, brad head, altered or clipped T-head for use with mechanical drivers, diamond or chisel point, smooth or barbed shank formed from round or square stock, as specified, bright finished.

TABLE 21 Type I, Style 15Flooring Nails^A

Note—Harded steel or steel wire, casing head or flat-cupped countersunk head, diamond or blunt point, round, smooth or mechanically deformed shank, dark (hardened), bright (steel wire) or cement coated, as specified.

TABLE 22 Type I, Style 16Lath Nails^A

Note—Steel wire, flat head, diamond point, round smooth shank, blued finish.

TABLE 23 Type I, Style 16Lath Nails^A

Note—Steel wire, flat hook-head, diamond point, round smooth shank, bright, blued, or zinc coated as specified.

TABLE 24 Type I, Style 17Masonry Nails^A

Note—Hardened steel, flat or flat countersunk head, diamond point, mechanically deformed shank, bright finish.

TABLE 25 Type I, Style 18Pallet Nails^A

Note—Hardened steel or steel wire (for mechanical drivers); flat head, altered or T-Head (for mechanical drivers); diamond, blunt diamond, blunt chisel or blunt point; round, mechanically deformed shank; bright finish (steel wire); or dark (hardened), as specified.

Dash No.	L	D	H	No. /Lb	Dash No.	L	D	H	No. Lb
01	1½	0.120	0.281	190	31	1¾	0.099	0.255	262
02	15/8	0.120	0.281	170	32	1¾	0.099	0.280	262
03	2	0.120	0.281	140	33	2	0.084	0.200	318
04	2¼	0.120	0.281	130	34	2	0.086	0.235	304
05	2½	0.120	0.281	120	35	2	0.090	0.245	277
06	2½	0.135	0.312	93	36	2	0.099	0.255	229
07	3	0.120	0.281	98	37	2	0.099	0.280	229
08	3	0.135	0.312	79	38	2	0.105	0.270	204
09	3	0.148	0.312	66	39	2	0.113	0.280	176
10	3¼	0.135	0.312	73	40	2¼	0.084	0.200	283
11	3¼	0.148	0.312	61	41	2¼	0.086	0.235	270
12	3½	0.148	0.312	57	42	2¼	0.099	0.255	204
13	3½	0.162	0.375	47	43	2¼	0.099	0.280	204
14	3½	0.177	0.438	38	44	2¼	0.105	0.270	181
15	4	0.177	0.438	35	45	2¼	0.113	0.280	156
16	4	0.177	0.375	35	46	2½	0.095	0.260	199
17	5	0.177	0.375	27	47	2½	0.099	0.255	183
18	6	0.177	0.375	23	48	2½	0.099	0.280	183
19	7	0.207	0.500	15	49	2½	0.113	0.280	141
20	8	0.207	0.500	13	50	2½	0.113	0.290	141
21	1¼	0.080	0.215	561	51	2½	0.120	0.290	125
22	1¼	0.099	0.255	367	52	2½	0.131	0.280	105
23	1¼	0.099	0.280	367	53	2¾	0.113	0.290	128
24	1½	0.080	0.215	468	54	2¾	0.120	0.285	113
25	1½	0.099	0.255	305	55	3	0.113	0.280	117
26	1½	0.099	0.280	305	56	3¼	0.120	0.290	96
27	15/8	0.105	0.270	251	57	3¼	0.131	0.280	81
28	1¾	0.084	0.200	364	58	3½	0.131	0.280	75
29	1¾	0.086	0.235	347	59	4	0.120	0.280	78
30	1¾	0.090	0.245	317	60	4	0.131	0.280	65

^A All dimensions are given in inches.

TABLE 26 Type I, Style 19Gypsum-Wallboard, Gypsumboard, and Drywall Nails^A

Note—Steel wire, flat head, diamond point, round smooth or deformed shank, bright or blued finish.

TABLE 27 Type I, Style 19Gypsum-Wallboard, Gypsumboard, and Drywall Nails^A

Note—Steel wire, flat slightly countersunk head, long diamond point, round mechanically deformed shank, bright or blued finish.

TABLE 28 Type I, Style 20Roofing Nails^A

Note—Aluminum alloy wire, flat head, diamond point, round smooth shank, or, when specified, square-barbed shank.

TABLE 29 Type I, Style 20Roofing Nails^A

Note—Steel wire; flat head; diamond point; round, smooth or deformed shank; bright or zinc coated, as specified, for hand driving or for use with mechanical drivers.

Dash No	L	D	H	No./lb	Dash No.	L	D	H	No./lb
01	¾	0.106	0.375	460	34	1¼	0.148	0.500	140
02	¾	0.120	0.438	340	35	1¼	0.162	0.500	120
03	¾	0.135	0.469	270	36	1½	0.106	0.375	...
04	¾	0.142	0.484	240	37	1½	0.120	0.438	180
05	¾	0.148	0.500	220	38	1¼	0.120	0.500	160
06	¾	0.162	0.500	200	39	1¼	0.135	0.469	150
07	7/8	0.106	0.375	...	40	1½	0.142	0.484	130
08	7/8	0.120	0.438	300	41	1½	0.148	0.500	120
09	7/8	0.120	0.500	250	42	1½	0.162	0.500	110
10	7/8	0.135	0.469	240	43	1¾	0.106	0.375	220
11	7/8	0.142	0.484	210	44	1¾	0.120	0.438	160
12	7/8	0.148	0.500	190	45	1¾	0.120	0.500	140
13	7/8	0.162	0.500	170	46	1¾	0.135	0.469	130
14	1	0.106	0.281	380	47	1¾	0.142	0.484	120
15	1	0.106	0.375	360	48	1¾	0.148	0.500	110
16	1	0.120	0.438	270	49	1¾	0.162	0.500	92
17	1	0.120	0.500	220	50	¾	0.120	0.375	290
18	1	0.135	0.469	210	51	7/8	0.120	0.375	259
19	1	0.142	0.484	190	52	1	0.120	0.375	232
20	1	0.148	0.500	170	53	1¼	0.120	0.375	209
21	1	0.162	0.500	150	54	1½	0.120	0.375	179
22	11/8	0.106	0.375	320	55	1¾	0.120	0.375	157
23	11/8	0.120	0.438	240	56	2	0.120	0.375	156
24	11/8	0.135	0.469	190	57	2	0.120	0.438	156
25	11/8	0.142	0.484	170	58	2½	0.120	0.375	125
26	11/8	0.148	0.500	160	59	2½	0.120	0.438	125
27	11/8	0.162	0.500	140	60	3	0.120	0.375	104
28	1¼	0.106	0.375	300	61	3	0.120	0.438	104
29	1¼	0.120	0.312	240	62	3½	0.120	0.375	89
30	1¼	0.120	0.438	220	63	3½	0.120	0.438	89
31	1¼	0.120	0.500	...	64	4	0.120	0.375	78
32	1¼	0.135	0.469	180	65	4	0.120	0.438	78
33	1¼	0.142	0.484	160	66	3	0.135	0.375	72
34	1¼	0.148	0.500	140	67	3½	0.135	0.375	62
35	1¼	0.162	0.500	120	68	4	0.148	0.406	46
36	1½	0.106	0.375	...	69	4½	0.148	0.406	40

^A All dimension are given in inches.

TABLE 30 Type I, Style 20Roofing Nails^A

Note—Copper-clad wire, flat head, diamond point, round smooth shank.

TABLE 31 Type I, Style 20Roofing Nails^A

Note—Steel wire; leak-resistant umbrella head; diamond point; round smooth or deformed shank; zinc coated.

Dash. No.	L	D	H	No./Lb
1	1¾	0.135	0.500	110
2	2	0.135	0.500	98
3	2	0.135	0.750	73
4	2	0.148	0.750	62
5	2	0.148	0.813	60
6	2½	0.135	0.750	64
7	2½	0.148	0.750	53
8	2½	0.148	0.813	53
9	3	0.148	0.813	47

^A All dimensions are given in inches.

TABLE 32 Type I, Style 20Roofing Nails^A

Note—Steel wire, flat reinforced head, needle or diamond point, round smooth shank, bright or zinc coated, as specified. (For prepared felt roofing.)

TABLE 33 Type I, Style 20Roofing Nails^A

Note—Hand-driven cap nails shall have a 1 in. diameter round plastic or steel cap with a cap diameter tolerance of ± 0.063 in., or a flat or domed square steel cap with an edge dimension 1 ± 0.063 in. Minimum thickness of the outside edge of plastic caps shall be 0.035 in. Minimum thickness of metal caps shall be 0.030 in.^† Nails are steel or stainless steel; with a diamond point; smooth or deformed shanks from round or spiral wire; and bright or zinc finish. Nails with metal caps shall both be bright or both have zinc finish. All hand-driven cap nails are packaged as integral nail-cap units.

F1667 NLRFD
			No/LbB
Dash No.	L	D	Steel	Plastic
	Hand Driven
01	½	0.105	130
02	5/8	0.105	120
03	¾	0.105	115	362
04	7/8	0.105	110	339
05	1	0.105	110	323
06	11/8	0.105	110
07	1¼	0.105	100	269
08		not used
09		not used
10		not used
11		not used
12	3	0.106	70	118
13	3	0.120	50	70
14	1½	0.105	96	219
15	1½	0.120	85	175
16	1¾	0.105	94	195
17	1¾	0.120	80	152
18	2	0.105	90	169
19	2	0.120	74	131
20	2½	0.105	80	138
21	2½	0.120	61	95
22	3½	0.148	53
23	4	0.148	32
24	5	0.162	25
25	6	0.162	20
26	8	0.162	13

^A All dimensions are given in inches.

^B Dashes () indicate that the fastener size is not a standard size.

^† Editorially corrected in March 2012.

TABLE 34 Type I, Style 20Roofing Nails^A

Note—Power driven cap nails have a 1 in. diameter plastic or steel cap with a cap diameter tolerance of ± 0.063 in. Minimum thickness of the outside edge of plastic caps is 0.035 in. Minimum thickness of metal caps is 0.010 in. Nails are steel or stainless steel; with a diamond point; smooth or deformed shanks from round or spiral wire; and bright or zinc finish. Nails with metal caps shall both be bright or both have zinc finish. With power driven cap nails, nails and caps may be packaged together or separately. Regardless of packaging, nails and caps are separately loaded into application tools with the nail being driven through the cap at point of application.

The nails used in the power driven cap nail systems are not considered roofing nails until they are combined with the cap.

F1667 NLRFD
			No/LbB
Dash No.	L	D	Steel	Plastic
	Power Driven
27	¾	0.120	185	268
28	7/8	0.083	200	400
29	7/8	0.120	168	240
30	1	0.083	196	355
31	1	0.120	154	215
32	1¼	0.080		320
33	1¼	0.083	190	310
34	1¼	0.120	140	190
35	1½	0.080		290
36	1½	0.083	183	280
37	1½	0.120	126	165
38	1¾	0.083	176	265
39	1¾	0.120	106	140
40	2	0.083	170	250
41	2	0.091		230
42	2	0.120	82	114

^A All dimensions are given in inches.

^B Dashes () indicate that the fastener size is not a standard size.

TABLE 35 Type I, Style 20Roofing Nails^A

Note—Aluminum alloy wire, flat head with neoprene washer (for aluminum roofing sheet), diamond point, round, smooth, or mechanically deformed shank, as specified.

TABLE 36 Type I, Style 21Shingle Nails^A

Note—Aluminum Alloy wire, flat head, diamond point, round, smooth or mechanically deformed shank, as specified.

TABLE 37 Type I, Style 21Shingle Nails^A

Note—Steel wire, flat head, diamond point, round, smooth (standard) or barbed (for special shingles) shank, bright or zinc coated, as specified.

TABLE 38 Type I, Style 22Siding Nails^A

Note—Aluminum alloy wire, flat head (insulated), casing or countersunk head (wood), as specified, diamond point, round smooth shank or, when specified, square-barbed shank.

TABLE 39 Type I, Style 23Slating Nails^A

Note—Aluminum alloy, copper or steel wire as specified. Aluminum and copper nails shall have a flat head (0.312 to 0.375–in. diameter), diamond point, and round smooth shank or, when specified, square-barbed shank. Steel nails shall have a flat, slightly countersunk head, diamond point, round smooth shank, zinc coated.

TABLE 40 Type I, Style 24Rubber Heel Nails^A

Note—Steel wire, flat or countersunk head, as specified, needle point, round smooth shank, bright finish.

TABLE 41 Type I, Style 25Underlayment Nails^A

Note—Steel wire, flat or flat, slightly countersunk head, diamond point, round, mechanically deformed shank, bright finish.

TABLE 42 Type I, Style 26Barbed Nails^A

Note—Steel wire, flat head, diamond point, square barbed shank, bright finish.

TABLE 43 Type I, Style 27Masonry Drive Nails^A

Note—Hardened steel, flat head, cone pilot point, round, high pitch, multiple-start threaded shank, bright finish. When specified, masonry drive nails shall be proof lead tested.

TABLE 44 Type I, Style 28Escutcheon Nails^A

Note—Steel or brass wire, as specified, oval head, diamond point, round smooth shank.

TABLE 45 Type I, Style 29Glulam Rivet^A

Note—Hardened steel, flat countersunk head, diamond point, smooth shank, zinc coated, as specified.

TABLE 46 Type I, Style 30Post-Frame Shank Nails^A

Note—Steel, flat head, diamond point, round, mechanically deformed shank, bright or zinc-coated as specified. Nails shall comply with the supplementary requirements of S1 and Table S1.2.

Dash No.	L	D	H	T1–D max	T1–D min	TL min	Pmax	Pmin	Root DiameterB
01	3	0.135	5/16	.010	.005	2.25	.077	.050	0.128
02	3	0.148	5/16	.010	.005	2.25	.077	.050	0.140
03	3	0.177	3/8	.010	.005	2.25	.077	.050	0.169
04	3.5	0.135	5/16	.010	.005	2.25	.077	.050	0.128
05	3.5	0.148	5/16	.010	.005	2.25	.077	.050	0.140
06	3.5	0.177	3/8	.010	.005	2.25	.077	.050	0.169
07	3.5	0.200	15/32	.010	.005	2.25	.077	.050	0.193
08	4	0.148	5/16	.010	.005	2.25	.077	.050	0.140
09	4	0.177	3/8	.010	.005	2.25	.077	.050	0.169
10	4	0.200	15/32	.010	.005	2.25	.077	.050	0.193
11	4	0.207	15/32	.010	.005	2.25	.077	.050	0.199
12	4.5	0.148	5/16	.010	.005	3	.077	.050	0.140
13	4.5	0.177	3/8	.010	.005	3	.077	.050	0.169
14	4.5	0.200	15/32	.010	.005	3	.077	.050	0.193
15	4.5	0.207	15/32	.010	.005	3	.077	.050	0.199
16	5	0.177	3/8	.010	.005	3	.077	.050	0.169
17	5	0.200	15/32	.010	.005	3	.077	.050	0.193
18	5	0.207	15/32	.010	.005	3	.077	.050	0.199
19	6	0.177	3/8	.010	.005	3	.077	.050	0.169
20	6	0.200	15/32	.010	.005	3	.077	.050	0.193
21	6	0.207	15/32	.010	.005	3	.077	.050	0.199
22	8	0.177	3/8	.010	.005	3	.077	.050	0.169
23	8	0.200	15/32	.010	.005	3	.077	.050	0.193
24	8	0.207	15/32	.010	.005	3	.077	.050	0.199

^A All dimensions are given in inches.

^B Root diameter is a calculated value and is not specified as a dimension to be measured.

L	=	length, in.,
H	=	head diameter, in.,
TL	=	length of threaded shank, in.,
max	=	maximum acceptable value (not subject to tolerances),
min	=	minimum acceptable value (not subject to tolerances),
D	=	shank diameter, in.,
T1	=	crest diameter, in., and
P	=	pitch, or spacing of threads, in.

TABLE 47 Type II, Style 1Common Cut Nails^A

Note—Steel or copper, flat head, bright finish.

TABLE 48 Type II, Style 2Basket Cut Nails^A

Note—Steel, flat head, bright finish.

TABLE 49 Type II, Style 3Clout Cut Nails^A

Note—Steel, flat head, bright finish, blued or zinc coated, as specified (see 5).

TABLE 50 Type II, Style 4Trunk Cut Nails^A

Note—Steel, oval head, bright finish, blued, brass or copper plated, as specified.

TABLE 51 Type II, Style 5Cobblers Cut Nails^A

Note—Steel casing head, clinch point, bright finish or brass plated, as specified.

TABLE 52 Type II, Style 6Extra-Iron Clinching Cut Nails^A

Note—Steel, casing head, clinch point, bright finish or blued, as specified.

TABLE 53 Type II, Style 7Hob Cut Nails^A

Note—Steel, square grooved head, clinch point, bright finish, or blued, as specified.

TABLE 54 Type III, Style 1Common Spikes^A

Note—These spikes shall be sheared from medium carbon sheet steel and shall have a wedged-shaped shank with a square point end narrower than the upset head end. They shall have a flat head, bright finish, or zinc coated, as specified.

TABLE 55 Type III, Style 2Gutter Spikes^A

Note—Steel wire, oval head, chisel point, flat head, diamond point, bright finish or zinc coated, as specified.

TABLE 56 Type III, Style 3Round Spikes^A

Note—Steel wire, oval countersunk head, chisel point, flat head, diamond point, bright finish or zinc coated, as specified.

F1667 SPRDCA					F1667 SPRDFA
Dash No.	S	L	D	H	Dash No.	L	D	H
01	40d	5	0.2625	0.531	01	8	0.312	0.625
02	50d	5½	0.283	0.562	02	8	0.312	0.750
03	60d	6	0.283	0.562	03	9	0.312	0.750
04	. . .	7	0.312	0.625	04	10	0.312	0.750
. . .	. . .	. . .	. . .	. . .	05	8	0.375	0.750

^A All dimensions are given in inches.

TABLE 57 Type III, Style 4Barge and Boat Spikes^A

Note—Wrought iron, hot rolled steel rod or steel wire, square, diamond or oval head, chisel point, bright finish or zinc coated, as specified.

TABLE 58 Type IV, Style 1Fence Staples^A

Note—Steel wire, bright finish or zinc coated, as specified.

TABLE 59 Type IV, Style 2Poultry Netting Staples^A

Note—Steel wire, zinc coated.

TABLE 60 Type IV, Style 3Flat Top Crown Staples^A

Note—Steel wire, aluminum alloy wire, bright finish, zinc coated, cement coated or chemically etched, as specified. (For use in power tools for fastening wood and other materials to wood.)

TABLE 62 Type IV, Style 3Flat Top Crown Staples^A

Note—Steel wire, chisel point, tin plated, zinc coated or lacquer finish, as specified, cohered together in strips. (For use in staple tackers or machines.) The number per strip shall be as specified and shall be suitable for use in the make and model of tool specified.

TABLE 63 Type IV, Style 4Round or “V” Crown Staple ^A

Note—Steel wire or copper-clad wire, bright finish, zinc coated, cement coated or chemically etched, as specified. (For use in power tools for fastening wood and other materials to wood.)

TABLE 64 Type IV, Style 5Preformed Staples^A

Note—Steel wire, chisel point, zinc or cement coated, as specified. Copper-clad wire, chisel point, tinned or other plated finish, as specified. (Hand driven.)

TABLE 65 Type IV, Style 6Electrical Staples^A

Note—Insulated or uninsulated, as specified.

TABLE 66 Type IV, Style 7Preformed Hoop Staple^A

TABLE 67 Type IV, Style 8-Cap Staples

Note—Cap staples are Type IV, Style 3, steel, flat top crown, with bright finish or zinc coated (as specified) staples, with a 1 in. diameter plastic cap having a cap diameter tolerance of ± 0.025 in. Minimum thickness of the outside edge of plastic caps is 0.035 in. Staples are driven with a hand (swung) or power tool with the staple being driven though the cap at point of application. Staples and caps may be packaged together or separately. Regardless of packaging, nails and caps are separately loaded into application tools with the staple being driven through the cap at point of application.

STC Staples-Cap Sets
Dash No.	Ga.	C	L
1	18	3/16	¾
2	18	3/16	7/8
3	18	3/16	1
4	18	3/16	1–1/8
5	18	3/16	1–3/16
6	18	3/16	1–½
7	18	5/16	¾
8	18	5/16	7/8
9	18	5/16	1
10	18	5/16	1–1/8
11	18	5/16	1–3/16
12	18	5/16	1–½
13	18	3/8	5/8
14	18	3/8	¾
15	18	3/8	7/8
16	18	3/8	1
17	18	3/8	1–1/8
18	18	3/8	1–¼
19	18	3/8	1–3/8
20	18	3/8	1–½
21	18	7/16	5/8
22	18	7/16	¾
23	18	7/16	7/8
24	18	7/16	1
25	18	7/16	1–1/8
26	18	7/16	1–¼
27	18	7/16	1–3/8
28	18	7/16	1–½
29	20	3/8	5/8
30	21	½	5/8
31	24	3/8	3/8