Abstract
These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for determining the following properties: product hardness; proof load by length measurement (Method 1), yield strength (Method 2), yield strength of austenitic stainless steel and nonferrous materials (Method 2A), and uniform hardness (Method 3); axial tension of full size products such as fasteners and studs; wedge tension of full size products such as fasteners and studs; tension of machined test specimens including yield point (by drop of the beam or halt of the pointer, autographic diagram, and total extension under load methods), yield strength (by offset, and extension under load methods), tensile strength, elongation, and reduction of area; and total extension at fracture. As for internally threaded fasteners including nonheat- and heat-treated nuts, tests are provided for the determination of product hardness, proof load, and cone proof load. Test for determining the surface and core hardnesses are, conversely, described for direct tension indicators, and through-hardened, carburized, stainless steel, and nonferrous washers. And finally, product hardness testing is described for rivets. The test method for determining embrittlement of metallic coated externally threaded fasteners is detailed as well.
Scope
1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers, direct tension indicators, and rivets.
1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. In the absence of any specified test requirement(s), these test methods shall apply.
1.3 These test methods describe mechanical tests for determining the following properties:
|
| Section |
| For Externally Threaded Fasteners: | 3 |
|  Product Hardness | 3.1 |
|  Proof Load | 3.2.1 |
|   Method 1, Length Measurement | 3.2.3 |
|   Method 2, Yield Strength | 3.2.4 |
|   Method 3, Uniform Hardness | 3.2.5 |
|  Axial Tension Testing of Full-Size Product | 3.4 |
|  Wedge Tension Testing of Full-Size Product | 3.5 |
|  Tension Testing of Machined Test Specimens | 3.6 |
|  Total Extension at Fracture Test | 3.7 |
| For Internally Threaded Fasteners: | 4 |
|  Product Hardness | 4.1 |
|  Proof Load Test | 4.2 |
|  Cone Proof Load Test | 4.3 |
| For Washers and Direct Tension Indicators: | 5 |
|  Product Hardness-General Requirements | 5.1 |
|  Through Hardened Washers | 5.2 |
|  Carburized Washers | 5.3 |
|  Stainless Steel and Nonferrous Washers | 5.4 |
|  Direct Tension Indicators | 5.5 |
|  Compression Load | 5.6 |
| For Rivets: | 6 |
|  Product Hardness | 6.1 |
| Test for Embrittlement of Metallic-Coated Externally Threaded   Fasteners | 7 |
| Test Method for Determining Decarburization and Carburization | 8 |
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: The values are stated in inch-pound for inch fasteners and SI metric units for metric fasteners.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
