BS EN 1594:2013

Gas infrastructure. Pipelines for maximum operating pressure over 16 bar. Functional requirements. | Status: Superseded, Withdrawn

1 Scope This European Standard is applicable to pipelines with a maximum operating pressure (MOP) over 16bar for the carriage of processed, non-toxic and non-corrosive natural gas according to EN ISO 13686 in onland gas infrastructure. This European Standard is also applicable to pipelines with a maximum operating pressure (MOP) over 16 bar for the carriage of non-conventional gases such as injected biomethane, complying with EN ISO 13686 and for which a detailed technical evaluation of the functional requirements is performed ensuring there are no other constituents or properties of the gases that can affect the integrity of the pipeline. Onland gas infrastructure is where:

• — pipeline elements are made of unalloyed or low-alloyed carbon steel;
• — pipeline elements are joined by welds, flanges or mechanical couplings;
• — the pipeline is not located within commercial or industrial premises as an integral part of the industrial process on these premises except for any pipelines and facilities supplying such premises;
• — the design temperature of the system is between －40 °C and 120 °C inclusive.

This European Standard applies to onshore pipeline systems from the point where the pipeline first crosses what is normally accepted as battery limit between on and offshore, e.g.:

• — first isolation valve;
• — the base of steep sea shelf;
• — above the high water/low water mark onto mainland;
• — an island.

This European Standard also applies to a pipeline system with a starting point onshore, also when parts of the pipeline system on the mainland subsequently cross fjords, lakes etc. This European Standard does not apply to existing pipelines, in use prior to the publication of this European Standard, nor to modifications to existing pipelines. Gas infrastructures covered by this European Standard begin after the gas producer's meet ring station. The functional demarcation of the pipeline system within a plant area will be determined from case to case. Generally speaking, this will be directly after the first isolating valve of the installation. This European Standard also describes the mechanical requirements for pipework in stations with a maximum operating pressure greater than 16 bar. Welding requirements are described in a special application standard on welding for gas infrastructures EN 12732. Functional requirements for stations are given in:

• — EN 1776 , Gas supply systems — Natural gas measuring stations — Functional requirements
• — EN 1918‑5 , Gas supply systems — Underground gas storage — Part 5: Functional recommendations for surface facilities
• — EN 12186 , Gas supply systems — Gaspressure regulating stations for transmission and distribution — Functional requirements
• — EN 12583 , Gas supply systems — Compressor stations — Functional requirements

This European Standard specifies common basic principles for gas infrastructures. Users of this European Standard should be aware that there may exist more detailed national standards and codes of practice in the CEN member countries. This European Standard is intended to be applied in association with these national standards and/or codes of practice setting out the above mentioned principles. In the event of conflicts in terms of more restrictive requirements in the national legislation/regulation with the requirements of this European Standard, the national legislation/regulation takes precedence as illustrated in CEN/TR 13737 (all parts).

NOTE CEN/TR 13737 (all parts) contains:

• — clarification of relevant legislation/regulations applicable in a country;
• — if appropriate, more restrictive national requirements;
• — national contact point for the latest information.

Reference is made in this European Standard to relevant European and other recognised standards for products used to construct and operate gas infrastructures. A schematic representation of pipelines for gas transmission is given in Figure 1. Figure 1 — Schematic representation of pipelines for gas supply over 16 bar Symbols Stations pipelines covered by this standard 1 P – well, production pipelines not covered by this standard 2 T – treatment pressure regulation 3 D – odorisation pressure safety system 4 S 1 – gas receiving metering system 5 S 2 – valve station compression 6 S 3 – delivery station valve 7 S 4 – compressor station isolation device 8 S 5 – other supply (e.g. for blending) 9 S 6 – export or import 10 S 7 – pressure regulating 11 S 8 – domestic distribution 12 S 9 – industrial distribution 13 S 10 – storage