BS EN 60079-11:2012 - Page 5

Explosive atmospheres. Equipment protection by intrinsic safety "i" | Status: Current, Superseded

1 Scope This part of IEC 60079 specifies the construction and testing of intrinsically safe apparatus intended for use in an explosive atmosphere and for associated apparatus, which is intended for connection to intrinsically safe circuits which enter such atmospheres. This type of protection is applicable to electrical equipment in which the electrical circuits themselves are incapable of causing an explosion in the surrounding explosive atmospheres. This standard is also applicable to electrical equipment or parts of electrical equipment located outside the explosive atmosphere or protected by another Type of Protection listed inIEC 60079‑0, where the intrinsic safety of the electrical circuits in the explosive atmosphere may depend upon the design and construction of such electrical equipment or parts of such electrical equipment. The electrical circuits exposed to the explosive atmosphere are evaluated for use in such an atmosphere by applying this standard. The requirements for intrinsically safe systems are provided inIEC 60079‑25. This standard supplements and modifies the general requirements of IEC 60079‑0, except as indicated inTable 1. Where a requirement of this standard conflicts with a requirement of IEC 60079‑0, the requirements of this standard shall take precedence. If requirements in this standard are applicable to both intrinsically safe apparatus and associated apparatus the term “apparatus” is used throughout the standard. This standard is for electrical equipment only; therefore the term “equipment” used in the standard always means “electrical equipment”. If associated apparatus is placed in the explosive atmosphere, it shall be protected by an appropriate Type of Protection listed inIEC 60079‑0, and then the requirements of that method of protection together with the relevant parts of IEC 60079‑0 also apply to the associated apparatus. Table 1 — Applicability of specific clauses of IEC 60079‑0 Clause or subclause of IEC 60079‑0 IEC 60079‑0 clause application to IEC 60079‑11 Intrinsically safe apparatus Associated apparatus Ed. 5.0 (2007) (informative) Ed. 6.0 (2011) (informative) Clause / Subclause title (normative) Group I and Group II Group III 1 1 Scope Applies Applies Applies 2 2 Normative references Applies Applies Applies 3 3 Terms and definitions Applies Applies Applies 4 4 Equipment grouping Applies Applies Applies 4.1 4.1 Group I Applies Excluded Applies 4.2 4.2 Group II Applies Excluded Applies 4.3 4.3 Group III Excluded Applies Applies 4.4 4.4 Equipment for a particular explosive atmosphere Applies Applies Applies 5.1 5.1 Environmental influences Applies Applies Applies 5.1.1 5.1.1 Ambient temperature Applies Applies Applies 5.1.2 5.1.2 External source of heating or cooling Applies Applies Applies 5.2 5.2 Service temperature Applies Applies Applies 5.3.1 5.3.1 Determination of maximum surface temperature Applies Applies Excluded 5.3.2.1 5.3.2.1 Group I electrical equipment Applies Excluded Excluded 5.3.2.2 5.3.2.2 Group II electrical equipment Applies Excluded Excluded 5.3.2.3 5.3.2.3 Group III electrical equipment Excluded Applies Excluded 5.3.3 5.3.3 Small component temperature for Group I or Group II electrical equipment Applies Excluded Excluded 6.1 6.1 General Applies Applies Applies 6.2 6.2 Mechanical strength of equipment Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 6.3 6.3 Opening times Excluded Excluded Excluded 6.4 6.4 Circulating currents in enclosures (e.g. of large electrical machines) Excluded Excluded Excluded 6.5 6.5 Gasket retention Excluded except when 6.1.2.3a)is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 6.6 6.6 Electromagnetic and ultrasonic radiating equipment Applies Applies Excluded 7.1.1 7.1.1 Applicability Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 7.1.2 7.1.2.1 Specification of materials Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 7.1.3 7.1.2.2 Plastic materials Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 7.1.4 7.1.2.3 Elastomers Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 7.2 7.2 Thermal endurance Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 7.3 7.3 Resistance to light Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 7.4 7.4 Electrostatic charges on external non-metallic materials Applies Applies Excluded NR 7.5 Accessible metal parts Applies Applies Excluded 7.5 NR Threaded holes Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 8.1 8.1 Material composition Applies Applies Excluded 8.1.1 8.2 Group I Applies Excluded Excluded 8.1.2 8.3 Group II Applies Excluded Excluded 8.1.3 8.4 Group III Excluded Applies Excluded 8.2 NR Threaded holes Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 9 9 Fasteners Excluded Excluded Excluded 10 10 Interlocking devices Excluded Excluded Excluded 11 11 Bushings Excluded Excluded Excluded 12 12 Materials used for cementing Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 13 13 Ex Components Applies Applies Applies 14 14 Connection facilities and termination compartments Excluded Excluded Excluded 15 15 Connection facilities for earthing or bonding conductors Excluded Excluded Excluded 16 16 Entries into enclosures Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 17 17 Supplementary requirements for rotating machines Excluded Excluded Excluded 18 18 Supplementary requirements for switchgear Excluded Excluded Excluded 19 19 Supplementary requirements for fuses Excluded Excluded Excluded 20 20 Supplementary requirements for plugs, socket outlets and connectors Excluded Excluded Excluded 21 21 Supplementary requirements for luminaires Excluded Excluded Excluded 22 22 Supplementary requirements for caplights and handlights Modified Modified Excluded 23.1 23.1 General Applies Applies Applies 23.2 23.2 Batteries Excluded Excluded Excluded 23.3 23.3 Cell types Applies Applies Applies 23.4 23.4 Cells in a battery Applies Applies Applies 23.5 23.5 Ratings of batteries Applies Applies Applies 23.6 23.6 Interchangeability Applies Applies Applies 23.7 23.7 Charging of primary batteries Applies Applies Applies 23.8 23.8 Leakage Applies Applies Applies 23.9 23.9 Connections Applies Applies Applies 23.10 23.10 Orientation Applies Applies Applies 23.11 23.11 Replacement of cells or batteries Applies Applies Applies 23.12 23.12 Replaceable battery pack Applies Applies Applies 24 24 Documentation Applies Applies Applies 25 25 Compliance of prototype or sample with documents Applies Applies Applies 26.1 26.1 General Applies Applies Applies 26.2 26.2 Test configuration Applies Applies Applies 26.3 26.3 Tests in explosive test mixtures Applies Applies Applies 26.4.1 26.4.1 Order of tests Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.4.1.1 26.4.1.1 Metallic enclosures, metallic parts of enclosures and glass parts of enclosures Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.4.1.2 26.4.1.2 Non-metallic enclosures or non-metallic parts of enclosures Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.4.1.2.1 26.4.1.2.1 Group I electrical equipment Excluded except when 6.1.2.3a) is applied Excluded Excluded except when 6.1.2.3a) is applied 26.4.1.2.2 26.4.1.2.2 Group II and Group III electrical equipment Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.4.2 26.4.2 Resistance to impact Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.4.3 26.4.3 Drop test Applies Applies Excluded except when 6.1.2.3a) is applied 26.4.4 26.4.4 Acceptance criteria Applies Applies Excluded except when 6.1.2.3a) is applied 26.4.5 26.4.5 Degree of protection (IP) by enclosures Applies Applies Applies 26.5.1.1 26.5.1.1 General Applies Applies Excluded 26.5.1.2 26.5.1.2 Service temperature Modified Modified Modified 26.5.1.3 26.5.1.3 Maximum surface temperature Modified Modified Modified 26.5.2 26.5.2 Thermal shock test Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.5.3 26.5.3 Small component ignition test (Group I and Group II) Applies Excluded Excluded 26.6 26.6 Torque test for bushings Excluded Excluded Excluded 26.7 26.7 Non-metallic enclosures or non-metallic parts of enclosures Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.8 26.8 Thermal endurance to heat Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.9 26.9 Thermal endurance to cold Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.10 26.10 Resistance to light Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 26.11 26.11 Resistance to chemical agents for Group I electrical equipment Excluded except when 6.1.2.3a) is applied Excluded Excluded 26.12 26.12 Earth continuity Excluded Excluded Excluded 26.13 26.13 Surface resistance test of parts of enclosures of non-metallic materials Applies Applies Excluded 26.15 26.14 Measurement of capacitance Applies Applies Excluded NR 26.15 Verification of ratings of ventilating fans Excluded Excluded Excluded NR 26.16 Alternative qualification of elastomeric sealing O-rings Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied 27 27 Routine tests Applies Applies Applies 28 28 Manufacturer’s responsibility Applies Applies Applies 29 29 Marking Applies Applies Applies 30 30 Instructions Applies Applies Applies Annex A (Normative) Annex A (Normative) Supplementary requirements for cable glands Excluded Excluded Excluded Annex B (Normative) Annex B (Normative) Requirements for Ex Components Applies Applies Applies Annex C (Informative) Annex C (Informative) Example of rig for resistance to impact test Applies Applies Excluded except when 6.1.2.3a) is applied Annex D (Informative) NR Alternative risk assessment method encompassing “equipment protection levels” for Ex equipment Applies Applies Applies Annex E (Informative) Annex D (Informative) Motors supplied by converters Excluded Excluded Excluded NR Annex E (Informative) Temperature rise testing of electric machines Excluded Excluded Excluded NR Annex F (Informative) Guideline flowchart for tests of non-metallic enclosures or non-metallic parts of enclosures (26.4) Excluded except when 6.1.2.3a) is applied Excluded except when 6.1.3 a) is applied. Excluded except when 6.1.2.3a) is applied Applies – This requirement of IEC 60079‑0 is applied without change. Excluded – This requirement of IEC 60079‑0 does not apply. Excluded except – This requirement of IEC 60079‑0 does not apply except when the conditions stated are met. Modified – This requirement of IEC 60079‑0 is modified as detailed in this standard. NR – No requirements.

NOTE The clause numbers in the above table are shown for information only. The applicable requirements of IEC 60079‑0 are identified by the clause title which is normative. This table was written against the specific requirements of IEC 60079‑0, ed. 6.0. The clause numbers for the previous edition are shown for information only. This is to enable the General requirements IEC 60079‑0, ed. 5.0, to be used where necessary with this part of IEC 60079. Where there were no requirements, indicated by NR, or there is a conflict between requirements, the later edition requirements take precedence.