What is PD IEC/TS 62647-1 - Preparing a lead-free control plan for ADHP electronic systems about?
PD IEC/TS 62647-1 is the first part of an international standard used for Process management for avionics. PD IEC/TS 62647-1 is useful in preparing the lead-free control plan that results in producing good quality ADHP electronic systems used in avionics.
PD IEC/TS 62647-1 defines the objectives of, and requirements for, documenting processes that assure customers and regulatory agencies that ADHP electronic systems containing Pb-free solder, piece parts, and PWBs will satisfy the applicable requirements for performance, reliability, airworthiness, safety, and certifiability throughout the specified life of performance.
This specification aims to communicate requirements for a lead-free control plan (LFCP), hereinafter referred to as the Plan, and to assist the Plan owners in the development of their own Plans. The Plan documents the Plan owner’s processes to assure their customers and all other stakeholders that the Plan owner’s products will continue to meet their requirements, given the risks stated in the Introduction. Pb-free risk management should be accomplished through specific requirements added to the Plan owner’s existing infrastructure of product management and control.
The control of the Pb-free activities will be accomplished by the Plan owner addressing the requirements of their customer. These activities include, but are not limited to, those performed by the system integrator, the original equipment manufacturer (OEM), and their respective supply chains, to the lowest level possible. This should be done with the knowledge that, at the component level, the aerospace industry may not have a great influence over those suppliers. In such cases, the Plan owner assumes responsibility.
Note: This specification does not contain detailed descriptions of the processes to be documented but lists high-level requirements for such processes, and areas of concern to the ADHP industries that need to be addressed by the processes.
Note: This specification applies to the ADHP electronics system supply chain. Some applications may have unique requirements that exceed the scope of this specification. The extended scope should be covered separately.
Note: The requirements of this specification may be tailored to address unique/specific program needs. If tailoring is performed, the user will obtain documented customer concurrence. Annex A provides a tailoring template that may be used.
Who is PD IEC/TS 62647-1 - Preparing a lead-free control plan for ADHP electronic systems for?
PD IEC/TS 62647-1 on Process management for avionics is useful for:
- Aerospace
- Manufacturer of electronic devices
- Defense
- Manufacturer of automotive parts
- Electronic engineer
Why should you use PD IEC/TS 62647-1 - Preparing a lead-free control plan for ADHP electronic systems?
Avionics are useful in communicating and navigating from one place to another place.
PD IEC/TS 62647-1 specifies the technical requirements for a lead-free control plan. This Configuration control and product identification are useful in assuring the appropriate traceability of the ADHP system. With the help of PD IEC/TS 62647-1, you can select the cost assemblies and sub-assemblies that contains Pb-free content. PD IEC/TS 62647-1 helps in understanding and organizing the plan that can be verified by your client.
By applying PD IEC/TS 62647-1 you can ensure the ADHP electronic systems are produced, supplied, reworked, repaired, or maintained by the Plan owner. Pb-free solder, piece parts, or PWBs helps in satisfying the requirements for performance, reliability, safety, and certifiability throughout the life span of these systems. This helps in preparing the lead-free control plan which results in manufacturing good quality ADHP electronic systems used in avionics.
What’s changed since the last update?
PD IEC/TS 62647-1:2012 supersedes PD IEC/PAS 62647-1:2011. PD IEC/TS 62647-1:2012 includes some technical changes with respect to PD IEC/PAS 62647-1:2011. These include:
- The addition of requirements for the use of Pb-free solder alloys
- The addition of requirements for the use of COTS
- The update of Annex B
